Fein ASCM 18 QM Select 71161164000 - Инструкция по эксплуатации - Страница 20

20

en

Secure the work piece firmly. 

A work piece that is 

gripped tightly in a clamping device or vice, is more 
secure than if held by hand.

Hold the power tool firmly. 

High reaction torque can 

briefly occur.

Do not machine any material containing asbestos. 

Asbes-

tos is cancerogenic.

Do not rivet or screw any name-plates or signs onto the 
power tool. 

If the insulation is damaged, protection 

against an electric shock will be ineffective. Adhesive 
labels are recommended.

Do not use accessories which are not specifically 
designed and recommended by the power tool manufac-
turer. 

Safe operation is not ensured merely because an 

accessory fits your power tool.

Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. 

The blower of the 

motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.

Never look or stare into the light of the power tool’s lamp 
from a short distance. Never point the light of the lamp 
into the eyes of other persons in close vicinity. 

The radi-

ation produced by the lamp can be harmful for the eye.

Do not direct the power tool against yourself, other per-
sons or animals. 

Danger of injury from sharp or hot 

application tools.

Use and handling of the battery (battery pack).

To avoid hazardous situations such as burns, fire, explo-
sion, skin injuries, and other injuries when handling the 
battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced 
in size. Do not subject batteries to mechanical impact or 
shock. 

Hazardous vapours and fluid can escape in case of 

damage and improper use of the battery. The vapours can 
irritate the respiratory system. Liquid ejected from the 
battery may cause skin irritations or burns.

When battery fluid from a damaged battery has come into 
contact with objects close by, check the respective com-
ponents, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store the 
battery in direct sunlight.

Do not remove the battery from its original packaging 
until it is going to be used.

Before any work on the machine itself, remove the bat-
tery from the power tool. 

If the power tool accidentally 

starts, there is danger of injury.

Remove the battery only when the power tool is switched 
off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture 
and water. 

Clean contaminated battery terminals and 

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended 
for your power tool. 

When working with and charging 

incorrect, damaged, repaired or reconditioned batteries, 
imitations or other brands, there is danger of fire and/or 
explosion.

Follow the safety warnings in the operating instructions 
of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information 
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare 
one tool with another. It may be used for a preliminary 
assessment of exposure.
The declared vibration emission level represents the 
main applications of the tool. However, if the tool is used 
for different applications, with different accessories or 
poorly maintained, the vibration emission may differ. 
This may significantly increase the exposure level over 
the total working period.
An estimation of the level of exposure to vibration 
should also take into account the times when the tool is 
switched off or when it is running but not actually doing 
the job. This may significantly reduce the exposure level 
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool 
and the accessories, keep the hands warm, organisation 
of work patterns.

Handling hazardous dusts

For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to 
one’s health.
Contact with or inhaling some dust types, e. g. asbestos 
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles 
from materials containing stone, paint solvents, wood 
preservatives, antifouling paints for vessels, can trigger 
allergic reactions to the operator or bystanders and/or 
lead to respiratory infections, cancer, birth defects or 
other reproductive harm. The risk from inhaling dusts 
depends on the exposition. Use dust extraction matched 
appropriately for the developing dust, as well as personal 
protective equipment and provide for good ventilation of 
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of grinding dust 
and chemical materials can self-ignite under unfavourable 
conditions or cause an explosion. Avoid sparking in the 
direction of the dust collector as well as overheating of 
the power tool and the materials being sanded, empty the 
dust collector/container in time, observe the material 
manufacturer’s working instructions, as well as the rele-
vant regulations in your country for the materials being 
worked.

Operating Instructions.

Adjust the rotational direction switch and the gear switch 
only when the machine is at a complete stop.
Always push the gear switch through to the stop. Other-
wise, the machine can become damaged.
Thermal overload of the power tool is indicated through 
flashing of the LED in the handle.
In case of overload, the machine switches off.
To avoid accidental starting, e. g., during transport, set 
the rotation selector switch to the centre position.

OBJ_BUCH-0000000268-001.book  Page 20  Thursday, December 22, 2016  11:31 AM