Einhell X-Change TE-CD 18-2 Li-i - Инструкция по эксплуатации - Страница 20

GB

- 20 -

5.  Before starting the equipment

 Be sure to read the following information before 

you use your cordless screwdriver for the 

fi

 rst 

time:

1.  Charge the battery pack with the charger 

supplied. An empty battery pack requires a 

charging period of approximately 0.5-1 hour.

2.   Only ever use sharp drill bits and screwdriver 

bits which are suitable for the purpose and in 

faultless condition.

3.   Always check for concealed electric cables 

and gas and water pipes when drilling and 

screwing in walls.

6. Operation

 6.1 Charging the LI battery pack (Fig. 2-3)

1.  Remove the battery pack (5) from the handle, 

pressing the pushlock buttons (8) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(6) into the mains socket outlet. The green 

LED will then begin to 

fl

 ash.

3.  Push the battery pack onto the battery char-

ger.

In section 10 “Charger indicator” you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to become charged, ple-

ase check

• 

 whether there is voltage at the socket-outlet

• 

 whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please 

return

• 

 the  charger

• 

 the battery pack

to our Customer Service Department.

To ensure that the LI battery pack provides 

long service you should take care to recharge 

it promptly. You must recharge the battery pack 

when you notice that the power of the cordless 

screwdriver drops. 

6.2 Torque setting (Fig. 4 / Item 1)

Important! The tool must be at a standstill 

when you set the torque with the setting ring.

The cordless hammer drill/screwdriver is 

fi

 tted 

with a mechanical torque selector.

The torque for a speci

fi

 c size of screw is selected 

with the set-collar (1). The correct torque depends 

on several factors:

• 

 on the type and hardness of material in ques-

tion

• 

 on the type and length screws used

• 

 on the requirements needing to be met by the 

screwed joint.

The clutch disengages with a grating sound to 

indicate when the set torque is reached.

6.3 Drilling/hammer drilling (Fig. 4) 

• 

 For drilling purpose, adjust the torque setting 

(1) to the setting “Drill”.

• 

 For hammer drilling purpose, adjust the 

torque setting (1) to the setting “Hammer”.

In the drill and hammer drill settings the slip cou-

pling is non-functional. The maximum torque is 

available for drilling and hammer drilling.

6.4 Changeover switch (Fig. 5/Item 3)

The slide switch above the On/O

ff

  switch is for 

setting the direction of rotation of the cordless 

screwdriver and for preventing the cordless 

screwdriver from being switched on inadvertently. 

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to 

the gearing, the direction of rotation must only be 

changed when the screwdriver is at a standstill. 

When the slide switch is in the middle position, 

the On/O

ff

  switch is blocked.

6.5 On/O

ff

  switch (Fig. 5 / Item 4)

In

fi

 nitely variable speed control is possible with 

the On/O

ff

  switch. The further you press the 

switch, the higher the speed of the battery-powe-

red drill/screwdriver. 

6.6  Changing over from 1st gear to 2nd gear 

(Fig. 6 / Item 7)

You can work at a higher or lower speed depen-

ding on the position of the selector switch. To avo-

id damaging the gear unit you should only change 

over gears when the tool has stopped.

Anl_TE_CD_18_2_Li_i_SPK7.indb   20

Anl_TE_CD_18_2_Li_i_SPK7.indb   20

14.07.14   11:14

14.07.14   11:14