Einhell TC-CD 18/35 Li - Инструкция по эксплуатации - Страница 21

GB

- 21 -

6. Operation

 6.1 Charging the LI battery pack (Fig. 2-3)

1.  Remove the battery pack (5) from the handle, 

pressing the pushlock buttons (7) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(6) into the mains socket outlet. The green 

LED will then begin to 

fl

 ash.

3.  Push the battery pack onto the battery char-

ger.

In section 10 “Charger indicator” you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to become charged, ple-

ase check

• 

 whether there is voltage at the socket-outlet

• 

 whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please 

return

• 

 the  charger

• 

 the battery pack

to our Customer Service Department.

To ensure that the LI battery pack provides 

long service you should take care to recharge 

it promptly. You must recharge the battery pack 

when you notice that the power of the cordless 

screwdriver drops. 

6.2 Torque setting (Fig. 4/Item 1)

Caution! 

Only ever adjust the setting ring when 

the equipment is at a standstill.

The cordless screwdriver is 

fi

 tted with a mechani-

cal torque selector.

The torque for a particular screw size is set with 

the setting ring (1). The torque is dependent on a 

number of factors:

• 

On the type and hardness of the material 

involved

• 

On the type and length of the screws used

• 

On the requirements that the screw connec-

tion has to satisfy

The grating disengagement of the coupling in-

dicates that the selected torque level has been 

reached.

6.3 Drilling (Fig. 4/Item 1)

For drilling purposes, adjust the setting ring for 

the torque to the last setting “Drill”. In the drill 

setting the slip coupling is non-functional. The 

maximum torque is available for drilling.

6.4 Changeover switch (Fig. 5/Item 3)

The slide switch above the On/O

ff

  switch is for 

setting the direction of rotation of the cordless 

screwdriver and for preventing the cordless 

screwdriver from being switched on inadvertently. 

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to 

the gearing, the direction of rotation must only be 

changed when the equipment is at a standstill. 

When the slide switch is in the middle position, 

the On/O

ff

  switch is blocked.

6.5 On/O

ff

  switch (Fig. 5/Item 4)

In

fi

 nitely variable speed control is possible with 

the On/O

ff

  switch. The further you push the 

switch, the higher the speed of the cordless 

screwdriver.

6.6  Battery capacity indicator (Fig. 6 – Item 2)

Press the battery capacity indicator switch (a). 

The battery capacity indicator (2) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

6.7 LED lamp (Fig. 6 / Item 9)

The LED lamp (9) can be used in poor lighting 

conditions to illuminate the area where you want 

to drill or screw. The LED lamp (9) will be lit au-

tomatically as soon as you press the ON/OFF 

switch (4).

6.8 Changing the tool (Fig. 7)

Important. 

Set the changeover switch (3) to its 

centre position whenever you carry out any work 

(for example changing the tool, maintenance 

work, etc.) on the cordless screwdriver.

Anl_TC_CD_18_35_Li_SPK9.indb   21

Anl_TC_CD_18_35_Li_SPK9.indb   21

08.06.2018   09:03:24

08.06.2018   09:03:24