Einhell PXC TE-CD 18/48 Li-i (2×2.0Ah) 4513935 - Инструкция по эксплуатации - Страница 22

GB

- 22 -

6.5 On/O

ff

  switch (Fig. 5 / Item 4)

In

fi

 nitely variable speed control is possible with 

the On/O

ff

  switch. The further you press the 

switch, the higher the speed of the battery-powe-

red drill/screwdriver. 

6.6  Changing over from 1st gear to 2nd gear 

(Fig. 4 / Item 7)

You can work at a higher or lower speed depen-

ding on the position of the selector switch. To avo-

id damaging the gear unit you should only change 

over gears when the tool has stopped.

6.7 Battery capacity indicator (Fig. 6 – Item 2)

Press the battery capacity indicator switch (a). 

The battery capacity indicator (2) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

6.8 LED lamp (Fig. 6 / Item 10)

The LED lamp (10) can be used in poor lighting 

conditions to illuminate the area where you want 

to drill or screw. The LED lamp (10) will be lit 

automatically as soon as you press the ON/OFF 

switch (4).

6.9 Changing the tool (Fig. 7)

Important. 

Set the changeover switch (3) to its 

centre position whenever you carry out any work 

(for example changing the tool, maintenance 

work, etc.) on the cordless screwdriver.

• 

 The cordless screwdriver is fitted with a 

quick-action chuck (9) with an automatic 

spindle stop.

• 

 Open the chuck (9). The chuck opening (a) 

must be large enough to hold the tool (drill bit 

or screwdriver bit).

• 

 Select the suitable tool. Push the tool as far 

as possible into the chuck opening (a).

• 

 Tighten the chuck (9) and then check that the 

tool is secure.

6.10 Screwdriving

We recommend using self-centering screws (e.g.  

Torx screws, recessed head screws) designed for 

reliable working. Be sure to use a bit that matches 

the screw in shape and size. Set the torque, as 

described elsewhere in these operating instruc-

tions, to suit the size of screw.

6.11 Mounting the additional handle 

  (Fig. 8 / Item 11)

The additional handle (11) enables you to achieve 

better stability while using the equipment.

Do not use the equipment without the additional 

handle.

The additional handle (11) can be screw-

fi

 tted 

in two positions (A, B). It is suitable therefore for 

right-handed and left-handed users.

7.  Cleaning, maintenance and 

ordering of spare parts

Danger!

Always pull out the battery pack before starting 

any cleaning work.

7.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

7.2 Maintenance

There are no parts inside the equipment which  

require additional maintenance.

Anl_TE_CD_18_48_Li_i_SPK9.indb   22

Anl_TE_CD_18_48_Li_i_SPK9.indb   22

07.03.2019   14:51:39

07.03.2019   14:51:39