Einhell PXC TE-CD 18/48 Li-i (2×2.0Ah) 4513935 - Инструкция по эксплуатации - Страница 21

GB

- 21 -

5.  Before starting the equipment

 Be sure to read the following information before 

you use your cordless screwdriver for the 

fi

 rst 

time:

1.  Charge the battery pack with the charger 

supplied. 

2.   Only ever use sharp drill bits and screwdriver 

bits which are suitable for the purpose and in 

faultless condition.

3.   Always check for concealed electric cables 

and gas and water pipes when drilling and 

screwing in walls.

6. Operation

 6.1 Charging the LI battery pack (Fig. 2-3)

1.  Remove the battery pack (5) from the handle, 

pressing the pushlock buttons (8) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(6) into the mains socket outlet. The green 

LED will then begin to 

fl

 ash.

3.  Push the battery pack onto the battery char-

ger.

In section 10 “Charger indicator” you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to become charged, ple-

ase check

• 

 whether there is voltage at the socket-outlet

• 

 whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please 

return

• 

 the  charger

• 

 the battery pack

to our Customer Service Department.

To ensure that the LI battery pack provides 

long service you should take care to recharge 

it promptly. You must recharge the battery pack 

when you notice that the power of the cordless 

screwdriver drops. 

6.2 Torque setting (Fig. 4 / Item 1)

Important! The tool must be at a standstill 

when you set the torque with the setting ring.

The cordless screwdriver is 

fi

 tted with a 

mechanical torque selector.

The torque for a speci

fi

 c size of screw is selected 

with the set-collar (1). The correct torque depends 

on several factors:

• 

 on the type and hardness of material in 

question

• 

 on the type and length screws used

• 

 on the requirements needing to be met by the 

screwed joint.

The clutch disengages with a grating sound to 

indicate when the set torque is reached.

6.3 Selector switch for driving/drilling/impact 

drilling (Fig. 4/Item 12)

• 

For driving purposes, set the selector switch 

(12) to the „Screw“ position. The torque is 

adjusted via the torque setting (1) (see point 

6.2).

• 

For drilling purposes, set the selector switch 

(12) to the „Bit“ position. The slip coupling is 

now off and the maximum torque is available 

regardless of the torque setting (1).

• 

For impact drilling purposes, set the selector 

switch (12) to the „Hammer“ position. The slip 

coupling is now off and the maximum torque 

is available regardless of the torque setting 

(1).

Important! Change the torque setting (1) and 

the selector switch for driving/drilling/impact 

drilling (12) only when the equipment is at a 

standstill.

6.4 Forward/Reverse switch (Fig. 5 / Item 3)

With the slide switch above the On/O

ff

  switch you 

can select the direction of rotation of the battery-

powered drill/screwdriver and secure it against 

being switched on accidentally. You can choose 

between clockwise and anticlockwise rotation. To 

avoid causing damage to the gearing it is advisa-

ble to change the direction of rotation only when 

the tool is at a standstill. The On/O

ff

  switch is blo-

cked when the slide switch is in centre position.

Anl_TE_CD_18_48_Li_i_SPK9.indb   21

Anl_TE_CD_18_48_Li_i_SPK9.indb   21

07.03.2019   14:51:39

07.03.2019   14:51:39