Einhell PXC TE-CD 18/40-1 Li 2×1.5 Ah Power X-Change - Инструкция по эксплуатации - Страница 21

GB

- 21 -

3.  Push the battery pack onto the battery char-

ger.

In section 10 “Charger indicator” you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to become charged, ple-

ase check

• 

 whether there is voltage at the socket-outlet

• 

 whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please 

return

• 

 the  charger

• 

 the battery pack

to our Customer Service Department.

To ensure that the LI battery pack provides 

long service you should take care to recharge 

it promptly. You must recharge the battery pack 

when you notice that the power of the cordless 

screwdriver drops. 

6.2 Torque setting (Fig. 4/Item 1)

Caution! 

Only ever adjust the setting ring when 

the equipment is at a standstill.

The cordless screwdriver is 

fi

 tted with a mechani-

cal torque selector.

The torque for a particular screw size is set with 

the setting ring (1). The torque is dependent on a 

number of factors:

• 

On the type and hardness of the material 

involved

• 

On the type and length of the screws used

• 

On the requirements that the screw connec-

tion has to satisfy

The grating disengagement of the coupling in-

dicates that the selected torque level has been 

reached.

6.3 Drilling (Fig. 4/Item 1)

For drilling purposes, adjust the setting ring for 

the torque to the last setting “Drill”. In the drill 

setting the slip coupling is non-functional. The 

maximum torque is available for drilling.

6.4 Forward/Reverse switch (Fig. 5 / Item 3)

With the slide switch above the On/O

ff

  switch you 

can select the direction of rotation of the battery-

powered drill/screwdriver and secure it against 

being switched on accidentally. You can choose 

between clockwise and anticlockwise rotation. To 

avoid causing damage to the gearing it is advisa-

ble to change the direction of rotation only when 

the tool is at a standstill. The On/O

ff

  switch is blo-

cked when the slide switch is in centre position.

6.5 On/O

ff

  switch (Fig. 5 / Item 4)

In

fi

 nitely variable speed control is possible with 

the On/O

ff

  switch. The further you press the 

switch, the higher the speed of the battery-powe-

red drill/screwdriver. 

6.6  Changing over from 1st gear to 2nd gear 

(Fig. 4 / Item 7)

You can work at a higher or lower speed depen-

ding on the position of the selector switch. To avo-

id damaging the gear unit you should only change 

over gears when the tool has stopped.

6.7 Battery capacity indicator (Fig. 6 – Item 2)

Press the battery capacity indicator switch (a). 

The battery capacity indicator (2) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

6.8 LED lamp (Fig. 6 / Item 10)

The LED lamp (10) can be used in poor lighting 

conditions to illuminate the area where you want 

to drill or screw. The LED lamp (10) will be lit 

automatically as soon as you press the ON/OFF 

switch (4).

Anl_TE_CD_18_40_1_Li_SPK9.indb   21

Anl_TE_CD_18_40_1_Li_SPK9.indb   21

06.11.2019   06:52:35

06.11.2019   06:52:35