Einhell PXC TE-CD 18/40-1 Li 2×1.5 Ah Power X-Change - Инструкция по эксплуатации - Страница 20

GB

- 20 -

Number of battery cells:  .................................... 5
Battery capacitance:  ................................. 1.5 Ah
Weight.......................................................1.46 kg

 The maximum screw diameter indicates the ma-

ximum diameter of the screw that can be screwed 

into wood. The screw diameter can vary depen-

ding on the type of wood.

Danger! 

Sound and vibration

Sound and vibration values were measured in 

accordance with EN 62841.

L

pA

 sound pressure level  ..................... 70.2 dB(A)

K

pA

 uncertainty  ............................................. 3 dB

L

WA

 sound power level ......................... 81.2 dB(A)

K

WA

 uncertainty ............................................. 3 dB

Wear ear-mu

ff

 s.

The impact of noise can cause damage to hea-

ring.

Total vibration values (vector sum of three direc-

tions) determined in accordance with EN 62841.

 Drilling in metal

Vibration emission value a

h

≤

 2.5 m/s

2

K uncertainty = 1.5 m/s

2

 The stated vibration emission levels and stated 

noise emission values were measured in ac-

cordance with a set of standardized criteria and 

can be used to compare one power tool with 

another.

The stated vibration emission levels and stated 

noise emission values can also be used to make 

an initial assessment of exposure.

Warning:

The vibration and noise emission levels may vary 

from the level speci

fi

 ed during actual use, depen-

ding on the way in which the power tool is used, 

especially the type of workpiece it is used for.

Keep the noise emissions and vibrations to a 

minimum.

• 

 Only use appliances which are in perfect wor-

king order.

• 

 Service and clean the appliance regularly.

• 

 Adapt your working style to suit the appliance.

• 

 Do not overload the appliance.

• 

 Have the appliance serviced whenever ne-

cessary.

• 

 Switch the appliance off when it is not in use.

• 

 Wear protective gloves.

Caution! 

Residual risks

Even if you use this electric power tool in 

accordance with instructions, certain resi-

dual risks cannot be rules out. The following 

hazards may arise in connection with the 

equipment’s construction and layout:

1.   Lung damage if no suitable protective dust 

mask is used.

2.   Damage to hearing if no suitable ear protec-

tion is used.

3.   Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and 

maintained.

 Limit the operating time. 

All stages of the operating cycle must be conside-

red (for example, times in which the electric tools 

are switched o

ff

  and times in which the tool is 

switched on but operates without load).

5.  Before starting the equipment

 Be sure to read the following information before 

you use your cordless screwdriver for the 

fi

 rst 

time:

1.  Charge the battery pack with the charger sup-

plied.

2.   Only ever use sharp drill bits and screwdriver 

bits which are suitable for the purpose and in 

faultless condition.

3.   Always check for concealed electric cables 

and gas and water pipes when drilling and 

screwing in walls.

6. Operation

 6.1 Charging the LI battery pack (Fig. 2-3)

1.  Remove the battery pack (5) from the handle, 

pressing the pushlock buttons (8) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(6) into the mains socket outlet. The green 

LED will then begin to 

fl

 ash.

Anl_TE_CD_18_40_1_Li_SPK9.indb   20

Anl_TE_CD_18_40_1_Li_SPK9.indb   20

06.11.2019   06:52:34

06.11.2019   06:52:34