DeWalt DCD701D2 - Инструкция по эксплуатации - Страница 8

6

English

Chargers

D

e

WALT

 chargers require no adjustment and are designed to be 

as easy as possible to operate.

Electrical Safety

The electric motor has been designed for one voltage only. 
Always check that the battery pack voltage corresponds to the 
voltage on the rating plate. Also make sure that the voltage of 
your charger corresponds to that of your mains.

Your 

D

e

WALT

 charger is double insulated in 

accordance with EN60335; therefore no earth wire 
is required.

If the supply cord is damaged, it must be replaced by a 
specially prepared cord available through the 

D

e

WALT

service organisation.

Mains Plug Replacement 
(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

•  Safely dispose of the old plug.
•  Connect the brown lead to the live terminal in the plug.
•  Connect the blue lead to the neutral terminal.

WARNING: 

No connection is to be made to the 

earth terminal.

Follow the fitting instructions supplied with good quality plugs. 
Recommended fuse: 3 A.

Using an Extension Cable

An extension cord should not be used unless absolutely 
necessary. Use an approved extension cable suitable for 
the power input of your charger (see 

Technical Data

). The 

minimum conductor size is 1 mm

2

; the maximum length 

is 30 m.
When using a cable reel, always unwind the cable completely.

Important Safety Instructions for All Battery 
Chargers

SAVE THESE INSTRUCTIONS:

 This manual contains important 

safety and operating instructions for compatible battery 
chargers (refer to 

Technical Data

).

•  Before using charger, read all instructions and cautionary 

markings on charger, battery pack, and product using 
battery pack.

WARNING: 

Shock hazard. Do not allow any liquid to get 

inside charger. Electric shock may result.

Residual Risks

In spite of the application of the relevant safety regulations 
and the implementation of safety devices, certain residual risks 
cannot be avoided. These are:

•  Impairment of hearing.
•  Risk of personal injury due to flying particles.
•  Risk of burns due to accessories becoming hot 

during operation.

•  Risk of personal injury due to prolonged use.

SAVE THESE INSTRUCTIONS

WARNING:

 We recommend the use of a residual current 

device with a residual current rating of 30mA or less.

CAUTION:

 Burn hazard. To reduce the risk of injury, 

charge only 

D

e

WALT

 rechargeable batteries. Other types of 

batteries may burst causing personal injury and damage.

CAUTION:

 Children should be supervised to ensure that 

they do not play with the appliance.

NOTICE: 

Under certain conditions, with the charger 

plugged into the power supply, the exposed charging 
contacts inside the charger can be shorted by foreign 
material. Foreign materials of a conductive nature such 
as, but not limited to, steel wool, aluminum foil or any 
buildup of metallic particles should be kept away from 
charger cavities. Always unplug the charger from the 
power supply when there is no battery pack in the cavity. 
Unplug charger before attempting to clean

• 

DO NOT attempt to charge the battery pack with any 
chargers other than the ones in this manual. 

The charger 

and battery pack are specifically designed to work together.

• 

These chargers are not intended for any uses other than 
charging 

D

e

WALT

 rechargeable batteries. 

Any other uses 

may result in risk of fire, electric shock or electrocution.

• 

Do not expose charger to rain or snow.

• 

Pull by plug rather than cord when disconnecting 
charger. 

This will reduce risk of damage to electric plug 

and cord.

• 

Make sure that cord is located so that it will not be 
stepped on, tripped over, or otherwise subjected to 
damage or stress.

• 

Do not use an extension cord unless it is absolutely 
necessary. 

Use of improper extension cord could result in risk 

of fire,electric shock, or electrocution.

• 

Do not place any object on top of charger or place 
the charger on a soft surface that might block the 
ventilation slots and result in excessive internal heat. 

Place the charger in a position away from any heat source. The 
charger is ventilated through slots in the top and the bottom 
of the housing.

• 

Do not operate charger with damaged cord or plug—

have them replaced immediately.

• 

Do not operate charger if it has received a sharp blow, 
been dropped, or otherwise damaged in any way.

 Take it 

to an authorised service centre.

• 

Do not disassemble charger; take it to an authorised 
service centre when service or repair is required.

 Incorrect 

reassembly may result in a risk of electric shock, electrocution 
or fire.

•  In case of damaged power supply cord the supply cord must 

be replaced immediately by the manufacturer, its service agent 
or similar qualified person to prevent any hazard.

• 

Disconnect the charger from the outlet before 
attempting any cleaning. This will reduce the risk of 
electric shock. 

Removing the battery pack will not reduce 

this risk.

• 

NEVER 

attempt to connect two chargers together.