DeWalt DCD701D2 - Инструкция по эксплуатации - Страница 7

5

English

Safety Instructions for All Operations

• 

Wear ear protectors when impact drilling. 

Exposure to 

noise can cause hearing loss.

• 

Hold power tool by insulated gripping surfaces, when 
performing an operation where the cutting accessory or 
the fastener may contact hidden wiring. 

Cutting accessory 

or the fastener contacting a “live” wire may make exposed 
metal parts of the power tool “live” and could give the operator 
an electric shock.

Safety Instructions When Using Long 

Drill Bits

• 

Never operate at higher speed than the maximum 
speed rating of the drill bit.

 At higher speeds, the bit is likely 

to bend if allowed to rotate freely without contacting the 
workpiece, resulting in personal injury.

• 

Always start drilling at low speed and with the bit tip 
in contact with the workpiece.

 At higher speeds, the bit is 

likely to bend if allowed to rotate freely without contacting the 
workpiece, resulting in personal injury.

• 

Apply pressure only in direct line with the bit and do not 
apply excessive pressure.

 Bits can bend causing breakage or 

loss of control, resulting in personal injury.

Additional Safety Warnings for Drills

• 

Use clamps or other practical way to secure and support 
the workpiece to a stable platform. 

Holding the work by 

hand or against your body is unstable and may lead to loss 
of control.

• 

Accessories and tool may get hot during operation. 

Wear 

gloves when handling them if performing heat producing 
applications such as drilling metals.

• 

Air vents often cover moving parts and should be 
avoided. 

Loose clothes, jewelry or long hair can be caught in 

moving parts.

unpredictable behaviour resulting in fire, explosion or risk 
of injury.

f ) 

Do not expose a battery pack or tool to fire or 
excessive temperature.

 Exposure to fire or temperature 

above 130 °C may cause explosion.

g ) 

Follow all charging instructions and do not charge 
the battery pack or tool outside the temperature 
range specified in the instructions. 

Charging 

improperly or at temperatures outside the specified range 
may damage the battery and increase the risk of fire. 

6)  Service

a ) 

Have your power tool serviced by a qualified repair 
person using only identical replacement parts.

This 

will ensure that the safety of the power tool is maintained.

b ) 

Never service damaged battery packs. 

Service 

of battery packs should only be performed by the 
manufacturer or authorized service providers.

4)  Power Tool Use and Care

a ) 

Do not force the power tool. Use the correct power 
tool for your application. 

The correct power tool 

will do the job better and safer at the rate for which it 
was designed.

b ) 

Do not use the power tool if the switch does not turn 
it on and off. 

Any power tool that cannot be controlled 

with the switch is dangerous and must be repaired.

c ) 

Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from 
the power tool before making any adjustments, 
changing accessories, or storing power tools. 

Such 

preventive safety measures reduce the risk of starting the 
power tool accidentally.

d ) 

Store idle power tools out of the reach of children 
and do not allow persons unfamiliar with the power 
tool or these instructions to operate the power tool. 

Power tools are dangerous in the hands of untrained users.

e ) 

Maintain power tools and accessories. Check for 
misalignment or binding of moving parts, breakage 
of parts and any other condition that may affect the 
power tool’s operation. If damaged, have the power 
tool repaired before use. 

Many accidents are caused by 

poorly maintained power tools.

f ) 

Keep cutting tools sharp and clean. 

Properly 

maintained cutting tools with sharp cutting edges are less 
likely to bind and are easier to control.

g ) 

Use the power tool, accessories and tool bits etc. 
in accordance with these instructions, taking into 
account the working conditions and the work to be 
performed. 

Use of the power tool for operations different 

from those intended could result in a hazardous situation.

h ) 

Keep handles and grasping surfaces dry, clean and 
free from oil and grease.

 Slippery handles and grasping 

surfaces do not allow for safe handling and control of the 
tool in unexpected situations.

5)  Battery Tool Use and Care

a ) 

Recharge only with the charger specified by the 
manufacturer.

 A charger that is suitable for one type 

of battery pack may create a risk of fire when used with 
another battery pack.

b ) 

Use power tools only with specifically designated 
battery packs.

 Use of any other battery packs may create 

a risk of injury and fire.

c ) 

When battery pack is not in use, keep it away from 
other metal objects, like paper clips, coins, keys, 
nails, screws or other small metal objects, that can 
make a connection from one terminal to another.

Shorting the battery terminals together may cause burns 
or a fire.

d ) 

Under abusive conditions, liquid may be ejected 
from the battery; avoid contact. If contact 
accidentally occurs, flush with water. If liquid 
contacts eyes, additionally seek medical help.

 Liquid 

ejected from the battery may cause irritation or burns.

e ) 

Do not use a battery pack or tool that is damaged or 
modified.

 Damaged or modified batteries may exhibit