CROWN CT10126C - Инструкция по эксплуатации - Страница 23

23

English

Power tool use and care

•

The persons with lowered psychophysical or men-

tal aptitudes as well as children can not operate the 

power tool, if they are not supervised or instructed 

about use of the power tool by a person responsible 

for their safety�

•

Do  not  force  the  power  tool.  Use  the  correct 

power  tool  for  your  application

� The correct power 

tool will do the job better and safer at the rate for which 

it was designed�

•

Do  not  use  the  power  tool  if  the  switch  does 

not turn it on and off.

 Any power tool that cannot be 

controlled with the switch is dangerous and must be 

repaired�

•

Disconnect the plug from the power source and / 

or the battery pack from the power tool before mak-

ing  any  adjustments,  changing  accessories,  or 

storing power tools

� Such preventive safety measures 

reduce the risk of starting the power tool accidentally�

•

Store  idle  power  tools  out  of  the  reach  of  chil-

dren and do not allow persons unfamiliar with the 

power  tool  or  these  instructions  to  operate  the 

power  tool.

 Power tools are dangerous in the hands 

of untrained users�

•

Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tool's op-

eration.  If  damaged,  have  the  power  tool  repaired 

before  use.

 Many accidents are caused by poorly 

maintained power tools�

•

Keep  cutting  tools  sharp  and  clean.

 Properly 

maintained cutting tools with sharp cutting edges are 

less likely to bind and are easier to control�

•

Use  the  power  tool,  accessories  and  tool  bits 

etc.  in  accordance  with  these  instructions,  taking 

into account the working conditions and the work 

to be performed. 

Use of the power tool for operations 

different from those intended could result in a hazard-

ous situation�

•

Keep  handles  and  grasping  surfaces  dry,  clean 

and  free  from  oil  and  grease.

 Slippery handles and 

grasping surfaces do not allow for safe handling and 

control of the tool in unexpected situations�

•

Note that when you operate a power tool, please 

hold the auxiliary handle correctly, which is helpful 

when controlling the power tool� Therefore, proper 

holding can reduce the risk of accidents or injuries�

Service

•

Have  your  power  tool  serviced  by  a  qualified 

repair  person  using  only  identical  replacement 

parts.

 This will ensure that the safety of the power tool 

is maintained�

•

Follow instruction for lubricating and changing ac-

cessories�

Special safety warnings

•

Use auxiliary handle(s), if supplied with the tool. 

Loss of control can cause personal injury�

•

Hold power tool by insulated gripping surfaces, 

when  performing  an  operation  where  the  cutting 

accessory  may  contact  hidden  wiring  or  its  own 

cord.

 Cutting accessory contacting a "live" wire may 

make exposed metal parts of the power tool "live" and 

could give the operator an electric shock�

Safety  guidelines  during  power  tool 

operation

•

The workpiece shall be fastened� Fixed devices or 

vice shall be used to fasten the workpiece, which will 

be more secure than holding the workpiece with your 

hands�

•

Considering that asbestos may cause cancer, 

asbestos-containing materials shall not be processed�

•

The power tool could be put down only after the 

parts of power tool is completely static� Accessory on 

the power tool might be clamped during work, which 

may make it difficult for you to control the power tool.

•

Power tool with damaged electric wires shall not be 

used� If electric wires of the power supply are damaged 

during the work, you shall not touch the damaged 

electric wires and shall pull out the plug immediately� 

Damaged electric wires will raise the risk of electric 

shock�

•

When using power tools outdoor, you must install 

fault current (FI) protection switch on the power tool�

•

Appropriate  detector  shall  be  used  to  find  the 

location of hidden power wires� Or you should obtain 

relevant information from local power supply unit� 

Drilling  electric  wires  will  cause  fire  and  electric 

shock� Damaged gas pipe will cause exploration� If 

water pipes are punctured, damage will be caused to 

property�

•

In case a accessory installed on the power tool 

is clamped, you shall shut down the power tool and 

stay calm� At that time, the power tool will produce 

extremely high reactive torque thus resulting in return 

stroke� The accessory installed on the power tool are 

likely to be clamped, for example: hypercharge of 

power tool or skewing of accessory installed on the 

power tool during work�

•

If hidden electric wires or power lines of the power 

tool itself might be cut off during work, you must hold 

the insulated handle to operate the power tool� When 

the power tool is in touch with a charged line, the metal 

parts on the power tool will conduct electricity and may 

cause the operator to get an electric shock�

•

During work, you must tightly hold the power tool 

and  ensure  you  stand  firmly.  You  should  hold  the 

power tool with your hands�

•

When operating and using the power tool, you can 

only hold switch position of the main handle rather than 

other parts�

•

Avoid stopping an power tool motor when loaded�

•

Never remove any chips or fragments with your 

power tool's motor running�

•

When working, follow the position of the power sup-

ply cable� Avoid winding it around your legs or arms�

•

Use only sharp drill bits without defects - it will make 

working with the power tool easier�

•

The modification of the drill bits design and the use 

of  removable  orifices  and  accessories  not  envisaged 

for this power tool is strictly forbidden�

•

Do not apply excessive pressure when operating the 

power tool - it can jam the drill bit and overload the en-

gine�

•

Do not allow drill bits to jam in the material pro-

cessed� If this occurs, do not try to release them by 

means of the power tool engine� This can put the pow-

er tool out of order�

•

Striking out drill bits jammed in the material pro-

cessed with a hammer or other objects is strictly for-

bidden - metal fragments can hurt both the operator 

and the people nearby�