Шуруповерты CROWN CT10049 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
14
English
Symbol
Meaning
A sign certifying that the
product complies with es-
sential requirements of the
EU directives and harmo-
nized EU standards�
Step speed controller posi-
tion�
Do not dispose of the power
tool in a domestic waste
container�
Power tool designation
Mixer is intended for miхing powdered building materi
-
als, such as lime, cement, mixes for plaster, materi-
als not containing the solvents, varnishes and similar
substances�
Power tool components
1
On / off switch
2
Ventilation slots
3
Step speed selector
4
Tool holder
5
Lock-on button
6
Speed selector thumbwheel *
7
Stirrer paddle *
8
Rod *
9
Wrench (22 mm) *
10
Wrench (19 mm) *
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the pow-
er tool it must be disconnected from the
mains.
Do not draw up the fastening ele-
ments too tight to avoid damaging the
thread.
Mounting / replacement of stirrer paddle (see fig. 1)
•
Screw the stirrer paddle
7
on the rod
8
and tighten
them with two wrenches
9
(22 mm) (see fig. 1.1).
•
While holding the tool holder
4
with spanner
10
(19
mm), screw the rod
8
(with the stirrer paddle
7
put on
it earlier) in, and tighten it with spanner
9
(22 mm) as
shown on fig. 1.2.
•
Disassembly operations do in reverse sequence�
Initial operating of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power tool on / off
Short-term switching on / off
To switch on, press and hold on / off switch
1
, to switch
off - release it�
Long-term switching on / off
Switching on:
Push on / off switch
1
and lock it in the position with
lock-on button
5
�
Switching off:
Push and release on / off switch
1
�
Design features of the power tool
Speed selector thumbwheel
Using speed selector thumbwheel
6
, you may select
the required stirrer paddle speed (also during opera-
tion)�
The required speed is dependent on the material and
can be determined with practical trials�
When operating your power tool at a low speed for a long
time, it has to be cooled down for 3 minutes� To do it, set
a maximum speed and leave your power tool to run idle�
Step speed selector switch
Attention: one can only change the revo-
lutions per minute range after the engine
fully stops.
The first speed
- you can find the values of
the revolutions per minute range in the tech-
nical specifications table.
The second speed
- you can find the val
-
ues of the revolutions per minute range in
the technical specifications table.
Recommendations on the power tool
operation
Stirring various substances
Do not process explosive substances
(for example, highly inflammable sol-
vents) and materials with ignition tem-
perature of lower than 21°С. Study the
manufacturer's instructions for such kind of mate-
rials carefully and stick to them.
•
The selection of stirring paddle type depends on the
type of substances stirred� Use stirring paddles with left-
hand blade spinning for low-viscosity substances (dis-
