CROWN CT10049 - Инструкция по эксплуатации - Страница 12

12

English

plugs  with  earthed  (grounded)  power  tools.

 Un-

modified  plugs  and  matching  outlets  will  reduce  risk 

of electric shock�

•

Avoid  body  contact  with  earthed  or  grounded 

surfaces,  such  as  pipes,  radiators,  ranges  and 

refrigerators.

 There is an increased risk of electric 

shock if your body is earthed or grounded�

•

Do not expose power tools to rain or wet condi-

tions.

 Water entering a power tool will increase the risk 

of electric shock�

•

Do  not  abuse  the  cord.  Never  use  the  cord  for 

carrying,  pulling  or  unplugging  the  power  tool. 

Keep  cord  away  from  heat,  oil,  sharp  edges  or 

moving parts.

 Damaged or entangled cords increase 

the risk of electric shock�

•

When  operating  a  power  tool  outdoors,  use  an 

extension  cord  suitable  for  outdoor  use.

 Use of a 

cord suitable for outdoor use reduces the risk of elec-
tric shock�

•

If  operating  a  power  tool  in  a  damp  location  is 

unavoidable,  use  a  residual  current  device  (RCD) 

protected  supply.

 Use of an RCD reduces the risk 

of electric shock� NOTE! The term "residual current 
device (RCD)" may be replaced by the term "ground 
fault circuit interrupter (GFCI)" or "earth leakage circuit 
breaker (ELCB)"�

•

Warning!

 Never touch the exposed metal sur-

faces on gearbox, shield, and so on because touch-
ing metal surfaces will be interfered with the elec-
tromagnetic wave, thus causing potential injury or 
accidents�

Personal safety

•

Stay  alert,  watch  what  you  are  doing  and  use 

common  sense  when  operating  a  power  tool.  Do 

not  use  a  power  tool  while  you  are  tired  or  under 

the  influence  of  drugs,  alcohol  or  medication.

 A 

moment of inattention while operating power tools may 
result in serious personal injury�

•

Use  personal  protective  equipment.  Always 

wear  eye  protection.

 Protective equipment such as 

dust mask, non-skid safety shoes, hard hat, or hearing 
protection used for appropriate conditions will reduce 
personal injuries�

•

Prevent  unintentional  starting.  Ensure  the 

switch  is  in  the  off-position  before  connecting  to 

power source and / or battery pack, picking up or 

carrying the tool

. Carrying power tools with your fin

-

ger on the switch or energising power tools that have 
the switch on invites accidents�

•

Remove  any  adjusting  key  or  wrench  before 

turning the power tool on.

 A wrench or a key left at-

tached to a rotating part of the power tool may result 
in personal injury�

•

Do not overreach. Keep proper footing and bal-

ance  at  all  times.

 This enables better control of the 

power tool in unexpected situations�

•

Dress  properly.  Do  not  wear  loose  clothing  or 

jewellery.  Keep  your  hair,  clothing  and  gloves 

away from moving parts.

 Loose clothes, jewellery or 

long hair can be caught in moving parts�

•

If  devices  are  provided  for  the  connection 

of  dust  extraction  and  collection  facilities,  en-

sure  these  are  connected  and  properly  used.

Use of dust collection can reduce dust-related 

hazards�

•

Do not let familiarity gained from frequent use of 

tools allow you to become complacent and ignore 

tool  safety  principles

� A careless action can cause 

severe injury within a fraction of a second�

•

Warning!

 Power tools can produces an elec-

tromagnetic field during operation� This field may 
under some circumstances interfere with active or 
passive medical implants� To reduce the risk of se-
rious or fatal injury, we recommend persons with 
medical implants to consult their physician and the 
medical implant manufacturer before operating this 
power tool�

Power tool use and care

•

The persons with lowered psychophysical or men-

tal aptitudes as well as children can not operate the 
power tool, if they are not supervised or instructed 
about use of the power tool by a person responsible 
for their safety�

•

Do  not  force  the  power  tool.  Use  the  correct 

power  tool  for  your  application

� The correct power 

tool will do the job better and safer at the rate for which 
it was designed�

•

Do not use the power tool if the switch does not 

turn it on and off.

 Any power tool that cannot be con-

trolled with the switch is dangerous and must be re-
paired�

•

Disconnect  the  plug  from  the  power  source 

and  /  or  the  battery  pack  from  the  power  tool  be-

fore  making  any  adjustments,  changing  accesso-

ries, or storing power tools

� Such preventive safety 

measures reduce the risk of starting the power tool 
accidentally�

•

Store  idle  power  tools  out  of  the  reach  of  chil-

dren and do not allow persons unfamiliar with the 

power  tool  or  these  instructions  to  operate  the 

power  tool.

 Power tools are dangerous in the hands 

of untrained users�

•

Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tool’s op-

eration.  If  damaged,  have  the  power  tool  repaired 

before  use.

 Many accidents are caused by poorly 

maintained power tools�

•

Keep  cutting  tools  sharp  and  clean.

 Properly 

maintained cutting tools with sharp cutting edges are 
less likely to bind and are easier to control�

•

Use  the  power  tool,  accessories  and  tool  bits 

etc.  in  accordance  with  these  instructions,  taking 

into account the working conditions and the work 

to be performed. 

Use of the power tool for operations 

different from those intended could result in a hazard-
ous situation�

•

Keep  handles  and  grasping  surfaces  dry,  clean 

and  free  from  oil  and  grease.

 Slippery handles and 

grasping surfaces do not allow for safe handling and 
control of the tool in unexpected situations�

•

Note that when you operate a power tool, please 

hold the auxiliary handle correctly, which is helpful 
when controlling the power tool� Therefore, proper 
holding can reduce the risk of accidents or injuries�

Service

•

Have  your  power  tool  serviced  by  a  qualified 

repair  person  using  only  identical  replacement