Bosch GSR 18 V-EC FC2 Solo 0.601.9E1.102 - Инструкция по эксплуатации - Страница 15

 English | 

15

Bosch Power Tools

1 609 92A 45S | (13.10.17)

The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with ano-
ther. It may be used for a preliminary assessment of exposu-
re.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This 
may significantly increase the exposure level over the total 
working period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working 
period.
Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns.

Assembly

Battery Charging



Use only the chargers listed in the technical data. 

Only 

these chargers are matched to the lithium-ion battery of 
your power tool.

Note: 

The battery supplied is partially charged. To ensure full 

capacity of the battery, completely charge the battery in the 
battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure 
does not damage the battery.

The lithium-ion battery is protected against deep discharging 
by the Electronic Cell Protection (ECP). When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.



Do not continue to press the On/Off switch after the 
machine has been automatically switched off. 

The bat-

tery can be damaged.

Removing the battery (see figure A)

To remove the battery pack 

4

, press the locking knob outward 

and pull out the battery pack out of the battery compartment.

Observe the notes for disposal.

Changing the Tool



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.

Inserting (see figure B)

Insert the application tool all the way into the mounting 

1

.

Mounting the keyless chuck (GFA FC2) or off-set angle 
adapter (GEA FC2) or angle drill head (GWA FC2)

 (see figure C)

Remove the application tool.

Insert the adapter into the mounting 

1

. Turn the locking ring 

10

 until it audibly engages.

Mounting the application tool in the keyless chuck 
(GFA FC2), off-set angle adapter (GEA FC2) or angle drill 
head (GWA FC2)
GFA FC2, GEA FC2 (see figure D):

Insert the tool in a twisting manner into the tool holder until it 
latches itself.

GWA FC2 (see figure E):

Open the drill chuck adapter 

7

 by turning it in direction of ro-

tation 



 until the application tool can be inserted. Insert the 

application tool.

Firmly tighten the sleeve of the drill chuck adapter 

7

 by tur-

ning it by hand in direction of rotation 



. This will automati-

cally lock the drill chuck.

Changing the position of engagement (see figure F)

Pull the locked adapter approx. 5 mm away from the power 
tool. Turn the adapter to the required position and then let it 
go. 

Removing the Adapter (see figure G)

Remove the application tool.

Unlock the adapter in the 

 direction and pull it off the 

mounting 

1

.

Dust/Chip Extraction



Dust from materials such as lead-containing coatings, so-
me wood types, minerals and metal can be harmful to one’s 
health. Touching or breathing-in the dust can cause allergic 
reactions and/or lead to respiratory infections of the user 
or bystanders.

GEA  FC 2

GFA FC 2

GWA FC 2

GEA  FC 2 GFA FC 2

GWA FC 2

Vibration total values ah (triax vec-
tor sum) and uncertainty K deter-
mined according to EN 60745-2-1.

Drilling in metal:
ah
K

Screwdriving:
ah
K

m/s

2

m/s

2

m/s

2

m/s

2

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

< 2,5

1,5

OBJ_BUCH-3365-001.book  Page 15  Friday, October 13, 2017  11:32 AM