Bosch GSR 10,8-2-LI - Инструкция по эксплуатации - Страница 14

14

 | English 

1 609 92A 1K5 | (15.12.15)

Bosch Power Tools

Noise/Vibration Information

Sound emission values determined according to 
EN 60745-2-1.

Typically the A-weighted sound pressure level of the product 
is 

71 dB(A). Uncertainty K = 3 dB.

The noise level when working can exceed 80 dB(A).

Wear hearing protection!

Vibration total values a

h

 (triax vector sum) and uncertainty K 

determined according to 

EN 60745-2-1.

Drilling into metal: a

h

< 2.5 m/s

2

, K = 1.5 m/s

2

Screwdriving without impact: a

h

< 2.5 m/s

2

, K = 1.5 m/s

2

The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This 
may significantly increase the exposure level over the total 
working period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working 
period.
Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation 
1194/2012), 2011/65/EU, until 19 April 2016: 
2004/108/EC, from 20 April 2016 on: 2014/30/EU, 
2006/42/EC including their amendments and complies with 
the following standards: EN 60745-1, EN 60745-2-1, 
EN 60745-2-2,  EN 50581.

Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 01.12.2015

Assembly

Battery Charging (see figure A)



Use only the battery chargers listed on the accessories 
page. 

Only these battery chargers are matched to the lith-

ium-ion battery of your power tool.

Note: 

The battery supplied is partially charged. To ensure full 

capacity of the battery, completely charge the battery in the 
battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure 
does not damage the battery.

The lithium-ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.



Do not continue to press the On/Off switch after the 
machine has been automatically switched off. 

The bat-

tery can be damaged.

To remove the battery 

5

 press the unlocking buttons 

4

 and 

pull out the battery downwards. 

Do not exert any force.

Observe the notes for disposal.

Changing the Tool (see figure B)



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.

The drill spindle is locked when the On/Off switch 

7

 is not 

pressed. This makes quick, convenient and easy changing of 
the tool in the drill chuck possible.

Open the keyless chuck 

1

 by turning in rotation direction 



, 

until the tool can be inserted. Insert the tool.

Firmly tighten the collar of the keyless chuck 

1

 by hand in ro-

tation direction 



.

Dust/Chip Extraction



Dust from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health. Touching or breathing-in the dust can cause 
allergic reactions and/or lead to respiratory infections of 
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment 
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dust can 

easily ignite.

Henk Becker
Executive Vice President
Engineering

Helmut Heinzelmann
Head of Product Certification
PT/ETM9

OBJ_BUCH-970-007.book  Page 14  Tuesday, December 15, 2015  12:41 PM