Bosch EasyDrill 18V-40 - Инструкция по эксплуатации - Страница 14

14

 | English

u

Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting ac-

cessory or fasteners may contact hidden wiring.

 Cut-

ting accessory or fasteners contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electric shock.

Safety instructions when using long drill bits

u

Never operate at higher speed than the maximum

speed rating of the drill bit.

 At higher speeds, the bit is

likely to bend if allowed to rotate freely without contact-

ing the workpiece, resulting in personal injury.

u

Always start drilling at low speed and with the bit tip

in contact with the workpiece.

 At higher speeds, the bit

is likely to bend if allowed to rotate freely without contact-

ing the workpiece, resulting in personal injury.

u

Apply pressure only in direct line with the bit and do

not apply excessive pressure.

Bits can bend causing

breakage or loss of control, resulting in personal injury.

Additional safety warnings

u

Hold the power tool securely. 

When tightening and

loosening screws be prepared for temporarily high torque

reactions.

u

Secure the workpiece.

 A workpiece clamped with

clamping devices or in a vice is held more secure than by

hand.

u

Use suitable detectors to determine if there are hid-

den supply lines or contact the local utility company

for assistance.

 Contact with electric cables can cause

fire and electric shock. Damaging gas lines can lead to ex-

plosion. Breaking water pipes causes property damage.

u

Always wait until the power tool has come to a com-

plete stop before placing it down.

 The application tool

can jam and cause you to lose control of the power tool.

u

In case of damage and improper use of the battery, va-

pours may be emitted. The battery can set alight or ex-

plode. 

Ensure the area is well ventilated and seek medical

attention should you experience any adverse effects. The

vapours may irritate the respiratory system.

u

Do not open the battery. 

There is a risk of short-circuit-

ing.

u

The battery can be damaged by pointed objects such

as nails or screwdrivers or by force applied externally.

An internal short circuit may occur, causing the battery to

burn, smoke, explode or overheat.

u

Only use the battery with products from the manufac-

turer.

 This is the only way in which you can protect the

battery against dangerous overload.

Protect the battery against heat, e.g. against

continuous intense sunlight, fire, dirt, water

and moisture.

 There is a risk of explosion and

short-circuiting.

u

Switch the power tool off immediately if the applica-

tion tool becomes blocked. Be prepared for high

torque reactions which cause kickback.

 The applica-

tion tool becomes blocked when it becomes jammed in

the workpiece or when the power tool becomes over-

loaded.

Product Description and

Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-

structions may result in electric shock, fire

and/or serious injury.

Please observe the illustrations at the beginning of this oper-

ating manual.

Intended use

The power tool is intended for driving and loosening screws

and for drilling in wood, metal, ceramic and plastic. The

cordless combi drill 

EasyImpact 18V-40

 is also designed for

impact drilling in brick.

Product Features

The numbering of the product features refers to the diagram

of the power tool on the graphics page.

(1)

Tool holder

(2)

Keyless chuck

(3)

Torque presetting ring

(4)

Operating mode presetting ring

(

EasyImpact 18V-40

)

(5)

Gear selector switch

(6)

Battery release button

a)

(7)

Rechargeable battery

a)

(8)

Worklight

(9)

Rotational direction switch

(10)

On/off switch

(11)

Handle (insulated gripping surface)

(12)

Universal bit holder

a)

a)

Accessories shown or described are not included with the

product as standard. You can find the complete selection of

accessories in our accessories range.

Technical Data

Cordless Drill/Driver

EasyDrill 18V-40

EasyImpact 18V-40

Article number

3 603 JD8 0..

3 603 JD8 1..

Rated voltage

V=

18

18

No-load speed

A)

1 609 92A 6MY | (14.09.2021)

Bosch Power Tools