BORT BSM-250 98295641 - Инструкция по эксплуатации - Страница 11

10

•  Dust from material such as paint containing lead, 

some wood species, minerals and metal may be 
harmful (contact with or inhalation of the dust may 
cause allergic reactions and/or respiratory diseases 
to the operator or bystanders); wear a dust mask 
and work with a dust extraction device when con-
nectable 

•  Certain kinds of dust are classi

fi

  ed as carcinogenic 

(such as oak and beech dust) especially in conjunc-
tion with additives for wood conditioning; wear a 
dust mask and work with a dust extraction device 
when connectable

•  Follow the dust-related national requirements for the 

materials you want to work with

•  When you put away the tool, switch off the motor 

and ensure that all moving parts have come to a 
complete standstill

•  Always disconnect plug from power source before 

making any adjustment or changing any accessory 
WHEN CONNECTING NEW 3-PIN PLUG (U.K. 
ONLY):

•  Do not connect the blue (= neutral) or brown (= live) 

wire in the cord of this tool to the earth terminal of 
the plug

•  If for any reason the old plug is cut off the cord of 

this tool, it must be disposed of safely and not left 
unattended

USE

• On/off 
•  Speed control for smooth starting  
•  Changing direction of rotation  
- when not properly set in left/right position, switch A  
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
•  Changing bits  
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
•  Torque control  
- output torque will increase as clutch ring D is rotated 
from 1 to 20; position E will lock up the clutch to permit 
drilling or driving heavy duty work
- when turning in a screw, 

fi

  rst try  position 1

and increase until the desired depth has been reached
•  Holding and guiding the tool 0
! while working, always hold the tool at the greycol-
oured grip area(s)
- keep ventilation slots G uncovered
- do not apply too much pressure on the tool; let the tool 
do the work for you

f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting 
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in 
accordance with these instructions, taking into account 
the working conditions and the work to be performed. 
Use of the power tool for operations different from 
those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a quali

fi

 ed  repair 

person using only identical replacement parts. 
This will ensure that the safety of the power tool is 
maintained.

SAFETY INSTRUCTIONS 
FOR DRILL/DRIVERS

•  Avoid damage that can be caused by screws, nails 

and other elements in your workpiece; remove them 
before you start working

•  Always check that the supply voltage is the same as 

the voltage indicated on the nameplate of the tool 
(tools with a rating of 230V or 240V can also be con-
nected to a 220V supply)

•  Use only accessories with an allowable speed 

matching at least the highest no-load speed of the 
tool

•  This tool should not be used by people under the 

age of 16 years

•  Use completely unrolled and safe extension cords 

with a capacity of 16 Amps (U.K. 13 Amps)

•  Always keep the cord away from moving parts of the 

tool

•  If the cord is damaged or cut through while working, 

do not touch the cord, but immediately disconnect 
the plug

•  Never use the tool when cord is damaged; have it 

replaced by a quali

fi

  ed person

•  If the drill bit becomes unexpectedly jammed (caus-

ing a sudden, dangerous reaction), immediately 
switch off the tool

•  In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the 
plug•  Secure the workpiece (a workpiece 
clamped with clamping devices or in a vice is held 
more securely than by hand)

•  Hold the power tool only by the insulated gripping 

surfaces when performing an operation where the 
accessory may contact hidden wiring or its own 
power cord (contact with a “live” wire will also make 
exposed metal parts of the power tool “live” and 
shock the operator)

•  Use suitable detectors to 

fi

 nd hidden utility lines or 

call the local utility company for assistance (contact 
with electric lines can lead to 

fi

  re or electrical shock; 

damaging a gas line can result in an explosion; pen-
etrating a water pipe will cause property damage or 
an electrical shock)

•  Do not work materials containing asbestos (asbes-

tos is considered carcinogenic)