AEG BSS18C2-0 4935478633 - Инструкция по эксплуатации - Страница 15

Шуруповерты AEG BSS18C2-0 4935478633 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.

Если остались вопросы, задайте их в комментариях после инструкции.

"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Страница:
/ 100
Загружаем инструкцию
background image

15

Never break open battery packs and chargers and store only 

in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme 

load or extreme temperatures. In case of contact with battery 

acid wash it o

  immediately with soap and water. In case of 

eye contact rinse thoroughly for at least 10 minutes and 

immediately seek medical attention.

Warning! 

To reduce the risk of 

fi

 re, personal injury, and 

product damage due to a short circuit, never immerse your 

tool, battery pack or charger in 

fl

 uid or allow a 

fl

 uid to 

fl

 ow 

inside them. Corrosive or conductive 

fl

 uids, such as seawater, 

certain industrial chemicals, and bleach or bleach containing 

products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The cordless impact driver can be used to tighten and loosen 

nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal 

use.

RESIDUAL RISK

Even when the product is used as prescribed, it is still 

impossible to completely eliminate certain residual risk 

factors. The following hazards may arise in use and the 

operator should pay special attention to avoid the following:
•  Injury caused by vibration.

Hold the product by designated handles and restrict 

working time and exposure.

•  Exposure to noise can cause hearing injury.

Wear ear protection and limit exposure.

•  Injury due to 

fl

 ying debris

Wear eye protection, heavy long trousers, gloves and 

substancial footwear at all times.

•  Inhalation of toxic dusts.

OPERATION

Note: It is recommended after fastening to always check 

the torque with a torque wrench.

The fastening torque is a

 ected by a wide variety of factors 

including the following.
•  State of battery charge – When the battery is discharged 

voltage will drop and the fastening torque will be reduced.

•  Operation at speeds – Operating the tool at low speeds will 

cause a reduction in fastening torques.

•  Fastening position – Holding the tool or the driving fastener 

in various angles will a

 ect the torque.

•  Drive accessory/socket – Failure to use the correct size 

accessory or socket, or a non-impact rated accessory may 

cause a reduction in the fastening torque.

•  Use of accessories and extensions – Depending on the 

accessory or extension 

fi

 tment can reduce the fastening 

force of the impact driver.

•  Bolt/Nut – Fastening torques may di

 er according to the 

diameter of the nut or bolt, the class of nut/bolt and the 

length of nut/bolt.

•  Condition of the fastener – Contaminated, corroded, dry or 

lubricated fasteners may vary the fastening torques.

•  Condition and base material – The base material of the 

fastener and any component in between the surfaces may 

e

 ect the fastening torque (Dry or lubricated base, soft or 

hard base, disc, seal or washer between fastener and base 

material).

IMPACTING TECHNIQUES

The longer a bolt, screw, or nut is impacted, the tighter it will 

become.
To help prevent damaging the fasteners or workpieces, avoid 

excessive impacting.
Be particularly careful when impacting smaller fasteners 

because they require less impacting to reach optimum torque.
Practice with various fasteners, noting the length of time 

required to reach the desired torque.
Check the tightness with a hand-torque wrench.
If the fasteners are too tight, reduce the impacting time.
If they are not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the head 

of the fastener a

 ects the degree of tightness.

The torque required to loosen a fastener averages 75% to 

80% of the tightening torque, depending on the condition of 

the contacting surfaces.
On light gasket jobs, run each fastener down to a relatively 

light torque and use a hand torque wrench for 

fi

 nal tightening.

NOTES FOR LI-ION BATTERIES

Use of Li-Ion batteries

Battery packs which have not been used for some time 

should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the 

performance of the battery pack. Avoid extended exposure to 

heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept 

clean.
For an optimum life-time, the battery packs have to be fully 

charged, after used. 
To obtain the longest possible battery life remove the battery 

pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 27°C 

and away from moisture

Store the battery packs in a 30% - 50% charged condition

Every six months of storage, charge the pack as normal.

Battery protection for Li-Ion Akkus

In extremely high torque, binding, stalling and short circuit 

situations that cause high current draw, the tool will vibrate for 

about 5 seconds, the fuel gauge will 

fl

 ash,and then the tool 

will turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the 

battery pack could raise too much. If this happens, the fuel 

gauge will 

fl

 ash until the battery pack cooled down. After the 

lights go o

 , the work may continue.

Transport of Lithium Batteries

Lithium-ion batteries are subject to the Dangerous Goods 

Legislation requirements.
Transportation of those batteries has to be done in 

accordance with local, national and international provisions 

and regulations.
•  The user can transport the batteries by road without further 

requirements.

•  Commercial transport of Lithium-Ion batteries by third 

parties is subject to Dangerous Goods regulations. 

Transport preparation and transport are exclusively to be 

carried out by appropriately trained persons and the 

process has to be accompanied by corresponding experts.

When transporting batteries:
•  Ensure that battery contact terminals are protected and 

insulated to prevent short circuit.

•  Ensure that battery pack is secured against movement 

within packaging.

ENGLISH

470 484 - BSS18C2.indd   15

470 484 - BSS18C2.indd   15

20.07.2021   11:41:04

20.07.2021   11:41:04

Полезные видео

Характеристики

Оцените статью
tehnopanorama.ru
Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)

Задать вопрос

Часто задаваемые вопросы
Как посмотреть инструкцию к AEG BSS18C2-0 4935478633?
Необходимо подождать полной загрузки инструкции в сером окне на данной странице
Руководство на русском языке?
Все наши руководства представлены на русском языке или схематично, поэтому вы без труда сможете разобраться с вашей моделью
Как скопировать текст из PDF?
Чтобы скопировать текст со страницы инструкции воспользуйтесь вкладкой "HTML"