AEG BSS18C2-0 4935478633 - Инструкция по эксплуатации - Страница 14

14

 BSS18C2

4831 46 01 XXXXXX MJJJJ

 18 

V

 0-2800 

min

-1

 0-3600 

min

-1

 210 

Nm

1/4" (6,35 mm)

 M18
 1,3...2,0 

kg

 -18...+50 

°C

L1815R, ... L1890R

AL18G, AL1218G, BL1218, BLK1218

96 dB(A) / 3 dB(A)

107 dB(A) / 3 dB(A)

 12,2 

m/s

2

 / 1,5 m/s

2

TECHNICAL DATA 

Type 
Production code 
Battery voltage 
No-load speed 
Impact range 
Torque 
Tool reception 
Max. diameter bolt / nut 
Weight according EPTA-Procedure 01/2014 (1.5 Ah...9.0 Ah) 
Recommended ambient operating temperature 
Recommended battery types 
Recommended charger 

Noise Information: 

Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K 
Sound power level / Uncertainty K

Wear ear protectors!
Vibration Information: 

Total vibration values (vector sum in the three axes) 

determined according to EN 62841.
Vibration emission value a

h  

/ Uncertainty K

Impact tightening of fasteners of the maximum capacity of the tool

WARNING

 Read all safety warnings, instructions, 

illustrations and speci

fi

 cations provided with this power 

tool.

 Failure to follow all instructions listed below may result 

in electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

IMPACT DRIVER SAFETY WARNINGS

Wear ear protectors.

 Exposure to noise can cause hearing 

loss.

Hold the power tool by insulated gripping surfaces, when 

performing an operation where the fastener may contact 

hidden wiring. 

Fasteners contacting a „live“ wire may make 

exposed metal parts of the power tool „live“ and could give 

the operator an electric shock.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when 

working with the machine. The use of protective clothing is 

recommended, such as dust mask, protective gloves, sturdy 

non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to 

health. Do not inhale the dust. Wear a suitable dust protection 

mask.
Do not machine any materials that present a danger to health 

(e.g. asbestos).
Switch the device o

ff

  immediately if the insertion tool stalls! 

Do not switch the device on again while the insertion tool is 

stalled, as doing so could trigger a sudden recoil with a high 

reactive force. Determine why the insertion tool stalled and 

rectify this, paying heed to the safety instructions.
The possible causes may be:

•  it is tilted in the workpiece to be machined

•  it has pierced through the material to be machined

•  the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.

•  when changing tools

•  when setting the device down
Chips and splinters must not be removed while the machine 

is running.
When working in walls ceiling, or 

fl

 oor, take care to avoid 

electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped 

workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the 

machine.
Do not dispose of used battery packs in the household refuse 

or by burning them. AEG Distributors o

ff

 er to retrieve old 

batteries to protect our environment.
Do not store the battery pack together with metal objects 

(short circuit risk).
Use only System GBS chargers for charging System GBS 

battery packs. Do not use battery packs from other systems.

WARNING

The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized 

test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of 

exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for 

di

ff

 erent applications, with di

ff

 erent accessories or poorly maintained, the vibration and noise emission may di

ff

 er. This may 

signi

fi

 cantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched 

o

ff

  or when it is running but not actually doing the job. This may signi

fi

 cantly reduce the exposure level over the total working 

period.
Identify additional safety measures to protect the operator from the e

ff

 ects of vibration and/or noise such as: maintain the tool 

and the accessories, keep the hands warm, organization of work patterns.

ENGLISH

Cordless Impact driver

470 484 - BSS18C2.indd   14

470 484 - BSS18C2.indd   14

20.07.2021   11:41:04

20.07.2021   11:41:04