AEG BSB18G4-0 4935478632 - Инструкция по эксплуатации - Страница 21

21

ENGLISH

The possible causes may be:

•  it is tilted in the workpiece to be machined

•  it has pierced through the material to be machined

•  the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use. 

WARNING! 

Danger of burns

•  when changing tools

•  when setting the device down
Chips and splinters must not be removed while the machine is 

running.
When working in walls ceiling, or floor, take care to avoid electric 

cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped 

workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the 

machine.
Do not dispose of used battery packs in the household refuse or 

by burning them. AEG Distributors offer to retrieve old batteries 

to protect our environment.
Do not store the battery pack together with metal objects (short 

circuit risk).
Use only System GBS chargers for charging System GBS 

battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in 

dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme 

load or extreme temperatures. In case of contact with battery 

acid wash it off immediately with soap and water. In case of eye 

contact rinse thoroughly for at least 10 minutes and immediately 

seek medical attention.

Warning! 

To reduce the risk of fire, personal injury, and product 

damage due to a short circuit, never immerse your tool, battery 

pack or charger in fluid or allow a fluid to flow inside them. 

Corrosive or conductive fluids, such as seawater, certain 

industrial chemicals, and bleach or bleach containing products, 

etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The electronic battery percussion drill/screwdriver may be 

used for drilling, percussion drilling, as well as screwdriving for 

independent use away from mains supply.
Do not use this product in any other way as stated for normal 

use.

RESIDUAL RISK

Even when the product is used as prescribed, it is still impossible 

to completely eliminate certain residual risk factors. The following 

hazards may arise in use and the operator should pay special 

attention to avoid the following:
•  Injury caused by vibration. 

Hold the product by designated handles and restrict working 

time and exposure.

•  Exposure to noise can cause hearing injury. 

Wear ear protection and limit exposure.

•  Injury due to flying debris 

Wear eye protection, heavy long trousers, gloves and 

substancial footwear at all times.

•  Inhalation of toxic dusts.

NOTES FOR LI-ION BATTERIES

Use of Li-Ion batteries

Battery packs which have not been used for some time should 

be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance 

of the battery pack. Avoid extended exposure to heat or sunshine 

(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully 

charged, after used. 
To obtain the longest possible battery life remove the battery 

pack from the charger once it is fully charged.
For battery pack storage longer than 30 days: 

Store the battery pack where the temperature is below 27°C and 

away from moisture 

Store the battery packs in a 30% - 50% charged condition 

Every six months of storage, charge the pack as normal.

Battery protection for Li-Ion Akkus

In extremely high torque, binding, stalling and short circuit 

situations that cause high current draw, the tool will vibrate for 

about 5 seconds, the fuel gauge will flash,and then the tool will 

turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the 

battery pack could raise too much. If this happens, the fuel 

gauge will flash until the battery pack cooled down. After the 

lights go off, the work may continue.

Transport of Lithium Batteries

Lithium-ion batteries are subject to the Dangerous Goods 

Legislation requirements.
Transportation of those batteries has to be done in accordance 

with local, national and international provisions and regulations.
•  The user can transport the batteries by road without further 

requirements.

•  Commercial transport of Lithium-Ion batteries by third parties is 

subject to Dangerous Goods regulations. Transport preparation 

and transport are exclusively to be carried out by appropriately 

trained persons and the process has to be accompanied by 

corresponding experts.

When transporting batteries:
•  Ensure that battery contact terminals are protected and insula-

ted to prevent short circuit.

•  Ensure that battery pack is secured against movement within 

packaging.

•  Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice

CLEANING

The ventilation slots of the machine must be kept clear at all 

times.

MAINTENANCE

Important note! If the carbon brushes are worn, in addition to 

exchanging the brushes the tool should be sent to after-sales 

service. This will ensure long service life and top performance.
Use only AEG accessories and spare parts. Should components 

need to be replaced which have not been described, please 

contact one of our AEG service agents (see our list of guarantee/

service addresses).
If needed, an exploded view of the tool can be ordered. Please 

state the machine type printed as well as the six-digit No. on 

the label and order the drawing at your local service agents or 

directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 

71364 Winnenden, Germany.

470 487 - BSB18G4.indd   21

470 487 - BSB18G4.indd   21

03.02.2021   09:34:32

03.02.2021   09:34:32