Skil 9005 - Инструкция по эксплуатации - Страница 9

9

•  Always disconnect plug from power source before 

making any adjustment or changing any accessory

ACCESSORIES

•  SKIL can assure flawless functioning of the tool only 

when original accessories are used

•  For mounting/using non-SKIL accessories observe the 

instructions of the manufacturer concerned

•  Use only grinding/cutting discs with a maximum 

thickness of 8 mm and a spindle hole diameter of 22 

mm

•  Never use reducors or adaptors to fit large-hole grinding/

cutting discs

•  Never use accessories with a “blind” threaded hole 

smaller than M14 x 21 mm

OUTDOOR USE

•  Connect the tool via a fault current (FI) circuit breaker 

with a triggering current of 30 mA maximum

BEFORE USE

•  Before using the tool for the first time, it is recommended 

to receive practical information

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the tool (tools with 

a rating of 230V or 240V can also be connected to a 

220V supply)

•  Always mount auxiliary handle E 

4

 and protective guard 

F 

4

; never use the tool without them

• 

Use suitable detectors to find hidden utility lines or 

call the local utility company for assistance

 (contact 

with electric lines can lead to fire or electrical shock; 

damaging a gas line can result in an explosion; 

penetrating a water pipe will cause property damage or 

an electrical shock)

• 

Do not work materials containing asbestos

 (asbestos 

is considered carcinogenic)

•  Dust from material such as paint containing lead, some 

wood species, minerals and metal may be harmful 

(contact with or inhalation of the dust may cause allergic 

reactions and/or respiratory diseases to the operator or 

bystanders); 

wear a dust mask and work with a dust 

extraction device when connectable

•  Certain kinds of dust are classified as carcinogenic (such 

as oak and beech dust) especially in conjunction with 

additives for wood conditioning; 

wear a dust mask and 

work with a dust extraction device when 

connectable

•  Follow the dust-related national requirements for the 

materials you want to work with

•  Be careful when cutting grooves, especially in supporting 

walls (slots in supporting walls are subject to country-

specific regulations; these regulations are to be observed 

under all circumstances)

• 

Secure the workpiece

 (a workpiece clamped with 

clamping devices or in a vice is held more securely than 

by hand)

•  Do not clamp the tool in a vice

•  Use completely unrolled and safe extension cords with a 

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

•  Inrush currents cause short-time voltage drops; under 

unfavourable power supply conditions, other equipment 

may be affected (if the system impedance of the power 

supply is lower than 0,25 Ohm, disturbances are unlikely 

to occur); if you need further clarification, you may 

contact your local power supply authority

•  If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug

•  Never use the tool when cord is damaged; have it 

replaced by a qualified person

•  In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the plug

•  In case of current interruption or when the plug is 

accidentally pulled out, unlock the on/off switch J 

4

immediately in order to prevent uncontrolled restarting

AFTER USE

•  After switching off the tool, never stop the rotation of the 

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

•  If for any reason the old plug is cut off the cord of this tool, 

it must be disposed of safely and not left unattended

USE

•  Mounting of accessories 

4

!  disconnect the plug

-  clean spindle A and all parts to be mounted

-  tighten clamping flange B with spanner C while 

pushing spindle-lock button D

!  push spindle-lock button D only when spindle A 

is at a standstill

-  for removing accessories handle vice-versa

!  grinding/cutting discs become very hot during 

use; do not touch them until they have cooled 

down

!  always mount backing pad when using sanding 

accessories

!  never use a grinding/cutting disc without the 

label (“blotter”) which is glued onto it (if 

provided)

•  Mounting of auxiliary handle E 

5

!  disconnect the plug

-  screw auxiliary handle E on the right, the top, or the left 

of the tool (depending on the work to be carried out)

•  Removing/mounting/adjusting of protective guard F 

6

!  disconnect the plug

!  ensure that the closed side of the protective 

guard always points to the operator

•  Before using the tool

-  ensure that accessory is correctly mounted and firmly 

tightened

-  check if accessory runs freely by turning it by hand

-  test-run tool for at least 30 seconds at highest no-load 

speed in a safe position

-  stop immediately in case of considerable vibration or 

other defects and check tool to determine the cause

•  On/off locking switch J 

7

-  switch on tool 

7

a

!  be aware of the sudden impact when the tool is 

switched on

!  before the accessory reaches the workpiece, the 

tool should run at full speed

-  lock switch 

7

b

-  unlock switch/switch off tool 

7

c