Skil 9005 - Инструкция по эксплуатации - Страница 8

8

into the pinch point can dig into the surface of the 

material causing the wheel to climb out or kick out. The 

wheel may either jump toward or away from the operator, 

depending on the direction of the wheel’s movement at 

the point of pinching. Abrasive wheels may also break 

under these conditions.

•  Kickback is the result of power tool misuse and/or 

incorrect operating procedures or conditions and can be 

avoided by taking proper precautions as given below.

a) 

Maintain a firm grip on the power tool and position 

your body and arm to allow you to resist kickback 

forces. Always use auxiliary handle, if provided, for 

maximum control over kickback or torque reaction 

during start-up. 

The operator can control torque 

reactions or kickback forces, if proper precautions are 

taken.

b) 

Never place your hand near the rotating accessory. 

The accessory may kickback over your hand.

c) 

Do not position your body in the area where power 

tool will move if kickback occurs. 

Kickback will propel 

the tool in the direction opposite to the wheel’s movement 

at the point of snagging.

d) 

Use special care when working corners, sharp 

edges etc. Avoid bouncing and snagging the 

accessory. 

Corners, sharp edges or bouncing have a 

tendency to snag the rotating accessory and cause loss 

of control or kickback.

e) 

Do not attach a saw chain woodcarving blade or 

toothed saw blade. 

Such blades create frequent 

kickback and loss of control.

3) SAFETY WARNINGS SPECIFIC FOR GRINDING AND 

ABRASIVE CUTTING-OFF OPERATIONS

a) 

Use only wheel types that are recommended for 

your power tool and the specific guard designed for 

the selected wheel. 

Wheels for which the power tool 

was not designed cannot be adequately guarded and are 

unsafe.

b) 

The grinding surface of the centre depressed 

wheels must be mounted below the plane of the 

guard lip.

 An improperly mounted wheel that projects 

through the plane of the guard lip cannot be adequately 

protected.

c) 

The guard must be securely attached to the power 

tool and positioned for maximum safety, so the least 

amount of wheel is exposed towards the operator. 

The guard helps to protect the operator from broken 

wheel fragments, accidental contact with wheel and 

sparks that could ignite clothing.

d) 

Wheels must be used only for recommended 

applications. 

For example: Do not grind with the side of 

a cut-off wheel. Abrasive cut-off wheels are intended for 

peripheral grinding; side forces applied to these wheels 

may cause them to shatter.

e) 

Always use undamaged wheel flanges that are of 

correct size and shape for your selected wheel. 

Proper wheel flanges support the wheel thus reducing 

the possibility of wheel breakage. Flanges for cut-off 

wheels may be different from grinding wheel flanges.

f) 

Do not use worn down wheels from larger power 

tools. 

A wheel intended for a larger power tool is not 

suitable for the higher speed of a smaller tool and may 

burst.

4) ADDITIONAL SAFETY WARNINGS SPECIFIC FOR 

CUTTING OFF OPERATIONS

a) 

Do not “jam” the cut-off wheel or apply excessive 

pressure. Do not attempt to make an excessive 

depth of cut. 

Overstressing the wheel increases the 

loading and susceptibility to twisting or binding of the 

wheel in the cut and the possibility of kickback or wheel 

breakage.

b) 

Do not position your body in line with and behind 

the rotating wheel. 

When the wheel, at the point of 

operation, is moving away from your body, the possible 

kickback may propel the spinning wheel and the power 

tool directly at you.

c) 

When the wheel is binding or when interrupting a 

cut for any reason, switch off the power tool and 

hold the power tool motionless until the wheel 

comes to a complete stop. Never attempt to remove 

the cut-off wheel from the cut while the wheel is in 

motion, otherwise kickback may occur. 

Investigate 

and take corrective action to eliminate the cause of wheel 

binding.

d) 

Do not restart the cutting operation in the 

workpiece. Let the wheel reach full speed and 

carefully re-enter the cut. 

The wheel may bind, walk up 

or kickback if the power tool is restarted in the workpiece.

e) 

Support panels or any oversized workpiece to 

minimize the risk of wheel pinching and kickback. 

Large workpieces tend to sag under their own weight. 

Supports must be placed under the workpiece near the 

line of cut and near the edge of the workpiece on both 

sides of the wheel.

f) 

Use extra caution when making a “pocket cut” into 

existing walls or other blind areas. 

The protruding 

wheel may cut gas or water pipes, electrical wiring or 

objects that can cause kickback.

5) SAFETY WARNINGS SPECIFIC FOR SANDING 

OPERATIONS

a) 

When sanding, do not use excessively oversized 

sanding disc paper. Follow the manufacturers’ 

recommendations when selecting sanding paper. 

Larger sanding paper extending beyond the sanding pad 

presents a laceration hazard and may cause snagging, 

tearing of the disc, or kickback.

6) SAFETY WARNINGS SPECIFIC FOR WIRE 

BRUSHING OPERATIONS

a) 

Be aware that wire bristles are thrown by the brush 

even during ordinary operation. Do not overstress 

the wires by applying excessive load to the brush. 

The wire bristles can easily penetrate light clothing and/ 

or skin.

b) 

If the use of a guard is recommended for wire 

brushing, do not allow any interference of the wire 

wheel or brush with the guard. 

Wire wheel or brush 

may expand in diameter due to work load and centrifugal 

forces.

GENERAL

•  This tool is not suitable for wet grinding/cutting

•  Only use the flanges which are supplied with this tool

•  This tool should not be used by people under the age of 

16 years