Skil 1215 - Инструкция по эксплуатации - Страница 7

7

•  Holding and guiding the tool 

6

-  guide the tool parallel to the working surface

!  while working, always hold the tool at the 

grey-coloured grip area(s)

!  do not apply too much pressure on the tool; let 

the sanding surface do the work for you

-  do not tilt the tool in order to avoid unwanted sanding 

marks

-  keep ventilation slots J 

2

 uncovered

APPLICATION ADVICE

•  For sanding bare wood surfaces move the tool in straight 

movements in line with the grain

•  For sanding all other surfaces move the tool in oval 

movements over the material

•  Mount sanding frame K (SKIL accessory 2610398244) 

for equalizing surfaces without scratches or grooves, and 

ensure it is in place securely 

7

!  sanding frame k becomes hot during use; do not 

touch it before it has cooled down

•  Never use the same sanding belt for wood and metal

•  Recommended sanding belt grits:

coarse -    for removing paint; for sanding of extremely 

rough wood

medium -  for sanding of rough or plain wood

fine -  

 for smoothing of wood; for finishing of bare 

wood; for smoothing surfaces with old paint

•  Use different grit sizes when the working surface is 

rough:

-  start sanding with coarse or medium grit

-  finish with fine grit

•  For more tips see www.skil.com

mAINTENANCE / SERVICE

•  This tool is not intended for professional use

•  Always keep tool and cord clean (especially ventilation 

slots J 

2

)

-  remove adhering sanding dust with a brush

!  disconnect the plug before cleaning

•  If the tool should fail despite the care taken in 

manufacturing and testing procedures, repair should be 

carried out by an after-sales service centre for SKIL 

power tools

-  send the tool 

undismantled

 together with proof of 

purchase to your dealer or the nearest SKIL service 

station (addresses as well as the service diagram of 

the tool are listed on www.skil.com)

ENVIRONmENT

• 

Do not dispose of electric tools, accessories and 

packaging together with household waste material

(only for EU countries)

-  in observance of European Directive 2012/19/EC on 

waste of electric and electronic equipment and its 

implementation in accordance with national law, 

electric tools that have reached the end of their life 

must be collected separately and returned to an 

environmentally compatible recycling facility

-  symbol 

8

 will remind you of this when the need for 

disposing occurs

DECLARATION OF CONFORmITY 

•  We declare under our sole responsibility that the product 

described under “Technical data” is in conformity with the 

following standards or standardization documents: EN 

60745, EN 61000, EN 55014, in accordance with the 

provisions of the directives 2004/108/EC, 2006/42/EC, 

2011/65/EU

• 

Technical file at

: SKIL Europe BV (PT-SEU/ENG1), 

4825 BD Breda, NL

¹ÊÁÂÆιƼ½ÊÇǾ¼½Æ

ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿

ÍÊÇȽƓˁ˅ʿ˂ ʽ¼¹Ɠ

Ĺ¾ ÁÂÿʹ¹¾

ÈÈÊÇιĹƹ¿½Ê

05.09.2014

NOISE/VIBRATION

•  Measured in accordance with EN 60745 the sound 

pressure level of this tool is 87 dB(A) and the sound 

power level 98 dB(A) (standard deviation: 3 dB), and the 

vibration 2.1 m/s² (hand-arm method; uncertainty 

K = 1.5 m/s²)

•  The vibration emission level has been measured in 

accordance with a standardised test given in EN 60745; it 

may be used to compare one tool with another and as a 

preliminary assessment of exposure to vibration when 

using the tool for the applications mentioned

-  using the tool for different applications, or with different 

or poorly maintained accessories, may significantly 

increase

 the exposure level

-  the times when the tool is switched off or when it is 

running but not actually doing the job, may significantly 

reduce

 the exposure level

!  protect yourself against the effects of vibration 

by maintaining the tool and its accessories, 

keeping your hands warm, and organizing your 

work patterns

Ponceuse à bande 

1210/1215

INTRODUCTION

•  Cet outil est conçu pour le ponçage à sec avec une 

grande capacité à enlever la matière du bois, plastique, 

métal et mastic et des surfaces peintes

•  Cet outil n’est conçu pour un usage professionnel

•  Lisez et conservez ce manuel d’instruction 

3

CARACTERISTIQUES TECHNIQUES 

1

ELEmENTS DE L’OUTIL 

2

A

  Interrupteur marche/arrêt

B

  Bouton de verrouillage de l’interrupteur marche/arrêt

C

  Levier pour changer la bande de ponçage

D

  Flèche