Skil 1215 - Инструкция по эксплуатации - Страница 6

6

e) 

maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tool’s 

operation. If damaged, have the power tool repaired 

before use.

 Many accidents are caused by poorly 

maintained power tools.

f) 

keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are less 

likely to bind and are easier to control.

g) 

Use the power tool, accessories and tool bits etc., in 

accordance with these instructions, taking into 

account the working conditions and the work to be 

performed.

 Use of the power tool for operations different 

from those intended could result in a hazardous situation.

5) SERVICE

a) 

Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

 This 

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

•  Avoid damage that can be caused by screws, nails and 

other elements in your workpiece; remove them before 

you start working

•  Always keep the cord away from moving parts of the tool; 

direct the cord to the rear, away from the tool

• 

Secure the workpiece

 (a workpiece clamped with 

clamping devices or in a vice is held more securely than 

by hand)

•  When you put away the tool, switch off the motor and 

ensure that all moving parts have come to a complete 

standstill

•  Use completely unrolled and safe extension cords with a 

capacity of 16 Amps (U.K. 13 Amps)

•  In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the plug

•  SKIL can assure flawless functioning of the tool only 

when original accessories are used

•  This tool should not be used by people under the age of 

16 years

•  The noise level when working can exceed 85 dB(A); wear 

ear protection

• 

Hold power tool by insulated gripping surfaces, 

because the belt may contact its own cord

 (cutting a 

“live” wire may make exposed metal parts of the power 

tool “live” and could give the operator an electric shock)

•  If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug

•  Never use the tool when cord is damaged; have it 

replaced by a qualified person

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the tool (tools with 

a rating of 230V or 240V can also be connected to a 

220V supply)

•  This tool is not suitable for wet sanding

• 

Do not work materials containing asbestos

 (asbestos 

is considered carcinogenic)

•  Dust from material such as paint containing lead, some 

wood species, minerals and metal may be harmful 

(contact with or inhalation of the dust may cause allergic 

reactions and/or respiratory diseases to the operator or 

bystanders); 

wear a dust mask and work with a dust 

extraction device when connectable

•  Certain kinds of dust are classified as carcinogenic (such 

as oak and beech dust) especially in conjunction with 

additives for wood conditioning; 

wear a dust mask and 

work with a dust extraction device when 

connectable

•  Follow the dust-related national requirements for the 

materials you want to work with

•  When sanding metal, sparks are generated; do not use 

dustbag/dustbox/vacuum cleaner and keep other 

persons and combustible material from work area

•  Do not touch the running sanding belt

•  Do not continue to use worn, torn or heavily clogged 

sanding belts

•  Wear protective gloves, safety glasses, close-fitting 

clothes and hair protection (for long hair)

•  Always disconnect plug from power source before 

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

•  If for any reason the old plug is cut off the cord of this tool, 

it must be disposed of safely and not left unattended

USE

•  On/off switch

-  switch on/off the tool by pulling/releasing trigger A 

2

!  before the sanding surface reaches the 

workpiece, you should switch on the tool

!  before switching off the tool, you should lift it 

from the workpiece

•  Switch locking for continuous use

-  pull trigger A 

2

-  press knob B 

2

 with your thumb

-  release the trigger

-  unlock the switch by pulling again trigger A 

2

 and 

then releasing it

•  Quick-changing of sanding belts (CLIC system) 

4

!  disconnect the plug

-  lift lever C

-  remove sanding belt

-  insert new belt with arrows printed at inner side of belt 

pointing in same direction as arrow D on tool

-  push lever back

!  change sanding belts in time

!  never fold sanding belts

•  Automatic belt centering (ABC)

-  centers belt automatically when switching on tool

-  keeps belt centered while sanding

In case belt runs off tool (mostly caused by inferior belt 

quality), you should

-  switch on the tool

-  adjust screw E 

2

 till the sanding belt is running in line 

with the flat side of the tool

-  use new belt, if belt still runs off tool

•  Dust suction 

5

-  empty dustbox G/dustbag F regularly for optimal dust 

pick-up performance

-  when using tool with vacuum cleaner, mount vacuum 

cleaner adaptor H as illustrated (

1215

)

-  when necessary, also clean the filter as illustrated

!  do not use dustbox/dustbag/vacuum cleaner 

when sanding metal