Ryobi RAG18X-0 (5133005011) - Инструкция по эксплуатации - Страница 3

Safety, performance, and dependability have been given 
top priority in the design of your angle grinder.

INTENDED USE

The angle grinder is intended to be used only by adults who 
have read and understood the instructions and warnings in 
this manual, and can be considered responsible for their 
actions. 
The product is designed for grinding and cutting metals 
and stone materials. Only appropriate grinding discs as 
described in the product speci

fi

 cations section of this 

manual should be 

fi

 tted to the angle grinder.

The product is intended for dry use only. Do not use the 
product for wet applications.
The product is designed for handheld use. The product is 
not to be mounted onto a workbench.
The product is intended for consumer use only. 
Do not use the product for any other purpose. Use of the 
product for operations different from intended could result in 
a hazardous situation.

WARNING!

Read all safety warnings, instructions, 

illustrations and specifications provided with this 
power tool.

 Failure to follow all instructions listed below 

may result in electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

SAFETY WARNINGS COMMON FOR GRINDING OR 
CUTTING-OFF OPERATIONS:

■

This power tool is intended to function as a grinder 
or cut-off tool. Read all safety warnings, instructions, 
illustrations and specifications provided with this 
power tool. 

Failure to follow all instructions listed below 

may result in electric shock, fire and/or serious injury.

■

Operations such as sanding, wire brushing, 
polishing or hole-cutting are not to be performed 
with this power tool. 

Operations for which the power 

tool was not designed may create a hazard and cause 
personal injury.

■

Do not convert this power tool to operate in a way 
which is not specifically designed and specified by 
the tool manufacturer.

 Such a conversion may result 

in a loss of control and cause serious personal injury.

■

Do not use accessories which are not specifically 
designed and specified by the tool manufacturer. 

Just because the accessory can be attached to your 
power tool, it does not assure safe operation.

■

The rated speed of the accessory must be at least 
equal to the maximum speed marked on the power 
tool. 

Accessories running faster than their rated speed 

can break and fly apart.

■

The outside diameter and the thickness of your 
accessory must be within the capacity rating of your 
power tool.

 Incorrectly sized accessories cannot be 

adequately guarded or controlled.

■

The dimensions of the accessory mounting must 
fit the dimensions of the mounting hardware of the 
power tool. 

Accessories that do not match the mounting 

hardware of the power tool will run out of balance, 
vibrate excessively and may cause loss of control.

■

Do not use a damaged accessory. Before each use 
inspect the accessory such as abrasive wheels for 
chips and cracks, backing pad for cracks, tear or 
excess wear, wire brush for loose or cracked wires. 
If power tool or accessory is dropped, inspect for 
damage or install an undamaged accessory. After 
inspecting and installing an accessory, position 
yourself and bystanders away from the plane of 
the rotating accessory and run the power tool at 
maximum no-load speed for one minute. 

Damaged 

accessories will normally break apart during this test 
time.

■

Wear personal protective equipment. Depending on 
application, use face shield, safety goggles or safety 
glasses. As appropriate, wear dust mask, hearing 
protectors, gloves and workshop apron capable of 
stopping small abrasive or workpiece fragments. 

The eye protection must be capable of stopping flying 
debris generated by various applications. The dust 
mask or respirator must be capable of filtrating particles 
generated by the particular application. Prolonged 
exposure to high intensity noise may cause hearing loss.

■

Keep bystanders a safe distance away from work 
area. Anyone entering the work area must wear 
personal protective equipment.

 Fragments of 

workpiece or of a broken accessory may fly away and 
cause injury beyond immediate area of operation.

■

Hold the power tool by insulated gripping surfaces 
only, when performing an operation where the 
cutting accessory may contact hidden wiring. 

Cutting accessory contacting a “live” wire may make 
exposed metal parts of the power tool “live” and could 
give the operator an electric shock.

■

Never lay the power tool down until the accessory 
has come to a complete stop. 

The spinning accessory 

may grab the surface and pull the power tool out of your 
control.

■

Do not run the power tool while carrying it at your 
side. 

Accidental contact with the spinning accessory 

could snag your clothing, pulling the accessory into your 
body.

■

Regularly clean the power tool’s air vents. T

he 

motor’s fan will draw the dust inside the housing and 
excessive accumulation of powdered metal may cause 
electrical hazards.

■

Do not operate the power tool near flammable 
materials. 

Sparks could ignite these materials.

■

Do not use accessories that require liquid coolants. 

Using water or other liquid coolants may result in 
electrocution or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged 
rotating wheel, backing pad, brush or any other accessory. 
Pinching or snagging causes rapid stalling of the rotating 
accessory which in turn causes the uncontrolled power tool 
to be forced in the direction opposite of the accessory’s 
rotation at the point of binding.
For example, if an abrasive wheel is snagged or pinched by 
the workpiece, the edge of the wheel that is entering into the 
pinch point can dig into the surface of the material causing 
the wheel to climb out or kick out. The wheel may either 
jump toward or away from the operator, depending on the 
direction of the wheel’s movement at the point of pinching. 
Abrasive wheels may also break under these conditions.

ENGLISH

EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL

3

Original Instructions