Makita GA5030X5 - Инструкция по эксплуатации - Страница 8

8 ENGLISH

Additional Safety Warnings:

17. 

When using depressed centre grinding wheels, 

be sure to use only fiberglass-reinforced 

wheels.

18. 

NEVER USE Stone Cup type wheels with this 

grinder.

 This grinder is not designed for these 

types of wheels and the use of such a product 

may result in serious personal injury.

19. 

Be careful not to damage the spindle, the 

flange (especially the installing surface) or the 

lock nut. Damage to these parts could result in 

wheel breakage.

20. 

Make sure the wheel is not contacting the 

workpiece before the switch is turned on.

21. 

Before using the tool on an actual workpiece, 

let it run for a while. Watch for vibration or 

wobbling that could indicate poor installation 

or a poorly balanced wheel.

22. 

Use the specified surface of the wheel to per

-

form the grinding.

23. 

Do not leave the tool running. Operate the tool 

only when hand-held.

24. 

Do not touch the workpiece immediately after 

operation; it may be extremely hot and could 

burn your skin.

25. 

Observe the instructions of the manufacturer 

for correct mounting and use of wheels. 

Handle and store wheels with care.

26. 

Do not use separate reducing bushings or 

adaptors to adapt large hole abrasive wheels.

27. 

Use only flanges specified for this tool.

28. 

For tools intended to be fitted with threaded 

hole wheel, ensure that the thread in the wheel 

is long enough to accept the spindle length.

29. 

Check that the workpiece is properly 

supported.

30. 

Pay attention that the wheel continues to 

rotate after the tool is switched off.

31. 

If working place is extremely hot and humid, 

or badly polluted by conductive dust, use a 

short-circuit breaker (30 mA) to assure opera-

tor safety.

32. 

Do not use the tool on any materials contain-

ing asbestos.

33. 

When use cut-off wheel, always work with 

the dust collecting wheel guard required by 

domestic regulation.

34. 

Cutting discs must not be subjected to any 

lateral pressure.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or famil-

iarity with product (gained from repeated 

use) replace strict adherence to safety 

rules for the subject product. MISUSE or 

failure to follow the safety rules stated in 

this instruction manual may cause serious 

personal injury.

FUNCTIONAL 

DESCRIPTION

CAUTION:

• 

Always be sure that the tool is switched off and 

unplugged before adjusting or checking function 

on the tool.

Shaft lock

► 

Fig.1:

1.

 Shaft lock

CAUTION:

• 

Never actuate the shaft lock when the spindle is 

moving. The tool may be damaged.

Press the shaft lock to prevent spindle rotation when 

installing or removing accessories.

Switch action

► 

Fig.2:

1.

 Switch lever

CAUTION:

• 

Before plugging in the tool, always check to 

see that the slide switch actuates properly and 

returns to the "OFF" position when the rear of 

the slide switch is depressed.

To start the tool, slide the switch lever toward the "I 

(ON)" position. For continuous operation, press the 

front of the switch lever to lock it. 

To stop the tool, press the rear of the switch lever, then 

slide it toward the "O (OFF)" position.

ASSEMBLY

CAUTION:

• 

Always be sure that the tool is switched off and 

unplugged before carrying out any work on the 

tool.

Installing side grip (handle)

► 

Fig.3

CAUTION:

• 

Always be sure that the side grip is installed 

securely before operation.

Screw the side grip securely on the position of the tool 

as shown in the figure.