Makita GA4540C - Инструкция по эксплуатации - Страница 6

6 

ENG902-1 

• 

The declared vibration emission value has been 
measured in accordance with the standard test 
method and may be used for comparing one tool 
with another. 

• 

The declared vibration emission value may also be 
used in a preliminary assessment of exposure. 

• 

The declared vibration emission value is used for 
main applications of the power tool. However if the 
power tool is used for other applications, the 
vibration emission value may be different. 

WARNING: 

• 

The vibration emission during actual use of the 
power tool can differ from the declared emission 
value depending on the ways in which the tool is 
used. 

• 

Be sure to identify safety measures to protect the 
operator that are based on an estimation of 
exposure in the actual conditions of use (taking 
account of all parts of the operating cycle such as 
the times when the tool is switched off and when it 
is running idle in addition to the trigger time). 
 

ENH101-16 

For European countries only 

EC Declaration of Conformity 

We Makita Corporation as the responsible 
manufacturer declare that the following Makita 
machine(s): 

Designation of Machine:   
Angle Grinder 
Model No./ Type: GA4040C, GA4540C, GA5040C, 
GA6040C, GA4541C, GA5041C 
are of series production and 

Conforms to the following European Directives: 

2006/42/EC 

And are manufactured in accordance with the following 
standards or standardised documents: 

EN60745 

The technical documentation is kept by:   

Makita International Europe Ltd. 
Technical Department, 
Michigan Drive, Tongwell, 
Milton Keynes, Bucks MK15 8JD, England 
 

30.8.2011 

000230 

Tomoyasu Kato 

Director 

Makita Corporation 

3-11-8, Sumiyoshi-cho, 

Anjo, Aichi, 446-8502, JAPAN 

GEA010-1 

General Power Tool Safety 
Warnings 

WARNING Read all safety warnings and all 

instructions.

 Failure to follow the warnings and 

instructions may result in electric shock, fire and/or 
serious injury. 

Save all warnings and instructions for 
future reference. 

GEB033-7 

GRINDER SAFETY WARNINGS 

Safety Warnings Common for Grinding, Sanding, 
Wire Brushing, or Abrasive Cutting-Off Operations: 

1. 

This power tool is intended to function as a 
grinder, sander, wire brush or cut-off tool. Read 
all safety warnings, instructions, illustrations 
and specifications provided with this power tool.

Failure to follow all instructions listed below may 
result in electric shock, fire and/or serious injury. 

2. 

Operations such as polishing are not 
recommended to be performed with this 
power tool.

 Operations for which the power tool 

was not designed may create a hazard and cause 
personal injury.   

3. 

Do not use accessories which are not 
specifically designed and recommended by 
the tool manufacturer.

 Just because the 

accessory can be attached to your power tool, it 
does not assure safe operation. 

4. 

The rated speed of the accessory must be at 
least equal to the maximum speed marked on 
the power tool.

 Accessories running faster than 

their rated speed can break and fly apart. 

5. 

The outside diameter and the thickness of your 
accessory must be within the capacity rating of 
your power tool.

 Incorrectly sized accessories 

cannot be adequately guarded or controlled. 

6. 

Threaded mounting of accessories must 
match the grinder spindle thread. For 
accessories mounted by flanges, the arbour 
hole of the accessory must fit the locating 
diameter of the flange.

 Accessories that do not 

match the mounting hardware of the power tool 
will run out of balance, vibrate excessively and 
may cause loss of control. 

7. 

Do not use a damaged accessory. Before each 
use inspect the accessory such as abrasive 
wheels for chips and cracks, backing pad for 
cracks, tear or excess wear, wire brush for 
loose or cracked wires. If power tool or 
accessory is dropped, inspect for damage or 
install an undamaged accessory. After 
inspecting and installing an accessory, 
position yourself and bystanders away from 
the plane of the rotating accessory and run the