Einhell TE-OS 18/230 Li (4460720) - Инструкция по эксплуатации - Страница 19

GB

- 19 -

ding/grinding paper coincide with the oscilla-

ting plate.

 5.4  Fastening the abrasive paper with the 

hook-and-loop fastening system (Fig. 7)

• 

 Only use sanding/grinding paper with the 

corresponding dimensions and matching per-

forations.

• 

 Place the sanding/grinding paper onto the 

oscillating plate (5) as shown in figure 7. 

6. Operation

6.1  Charging the LI battery pack (Fig. 8/9)

1.  Remove the battery pack (a) from the handle, 

pressing the pushlock buttons (b) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(c) into the mains socket outlet. The green 

LED will then begin to 

fl

 ash.

3.  Push the battery pack onto the battery char-

ger.

In section 10 “Charger indicator” you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

Store the rechargeable battery, cordless tool and 

charger in a dry place with an ambient tempera-

ture of: Rechargeable battery = 10-20°C

Cordless tool, charger = 10-40°C.

If the battery pack fails to become charged, ple-

ase check

• 

 whether there is voltage at the socket-outlet

• 

 whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please 

return

• 

 the  charger

• 

 the battery pack

to our Customer Service Department.

To ensure that items are properly packaged 

and delivered when you send them to us, 

please contact our customer service or the 

point of sale at which the equipment was 

purchased.

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

6.2  Battery capacity indicator 

(Fig. 10 – Item e)

Press the battery capacity indicator switch (d). 

The battery capacity indicator (e) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

 6.3  Switching the equipment ON/OFF  

(Fig. 11)

To switch on:

Push the ON/OFF switch (1) forwards.

To switch o

ff

 :

Push back the ON/OFF switch into its starting 

position.

6.4  Speed control (Fig. 12/Item 6)

To pre-select the speed turn the knurled screw (6) 

on the switch.

Plus direction:  

Higher speed

Minus direction:  

Lower speed

6.5  Working with the orbital grinder/sander

• 

 Place the whole surface area of the sanding 

disk on the material.

• 

 Switch on the machine and move it with gent-

le pressure over the workpiece completely 

circular movements or moving it to and fro 

and up and down.

• 

 Use a coarse paper for coarse sanding and a 

finer paper for finish sanding. You can find the 

Anl_TE-OS_18_230_Li_Solo_SPK9.indb   19

Anl_TE-OS_18_230_Li_Solo_SPK9.indb   19

05.10.2020   11:04:33

05.10.2020   11:04:33