Einhell TE-OS 18/230 Li (4460720) - Инструкция по эксплуатации - Страница 18

GB

- 18 -

L

pA

 sound pressure level  ..................... 76.8 dB(A)

K

pA

 uncertainty  ............................................. 3 dB

L

WA

 sound power level   ....................... 87.8 dB(A)

K

WA

 uncertainty ............................................. 3 dB

Wear ear-mu

ff

 s.

The impact of noise can cause damage to hea-

ring.

Total vibration values (vector sum of three direc-

tions) determined in accordance with EN 62841.

Handle

Vibration emission value a

h

 = 6.624 m/s

2

K uncertainty = 1.5 m/s

2

Additional handle

Vibration emission value a

h

 = 8.667 m/s

2

K uncertainty = 1.5 m/s

2

The stated vibration emission levels and stated 

noise emission values were measured in ac-

cordance with a set of standardized criteria and 

can be used to compare one power tool with 

another.

The stated vibration emission levels and stated 

noise emission values can also be used to make 

an initial assessment of exposure.

Warning:

The vibration and noise emission levels may vary 

from the level speci

fi

 ed during actual use, depen-

ding on the way in which the power tool is used, 

especially the type of workpiece it is used for.

Keep the noise emissions and vibrations to a 

minimum.

• 

 Only use appliances which are in perfect wor-

king order.

• 

 Service and clean the appliance regularly.

• 

 Adapt your working style to suit the appliance.

• 

 Do not overload the appliance.

• 

 Have the appliance serviced whenever ne-

cessary.

• 

 Switch the appliance off when it is not in use.

• 

 Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in 

accordance with instructions, certain resi-

dual risks cannot be rules out. The following 

hazards may arise in connection with the 

equipment’s construction and layout:

1.   Lung damage if no suitable protective dust 

mask is used.

2.   Damage to hearing if no suitable ear protec-

tion is used.

3.   Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and 

maintained.

5.  Before starting the equipment

Warning!

Always remove the battery pack before making 

adjustments to the equipment.

5.1  Fitting the dust collection box (Fig. 2)

The dust collection box (3) must be pushed onto 

the connector for the dust collection box (f).

To remove the dust collection box (3), pull the 

dust collection box to the rear and o

ff

 .

The dust is extracted directly into the dust coll-

ection box through the abrasive paper and the 

oscillating plate.

5.2  Fitting the dust extractor adapter (Fig. 13)

Slip the dust extractor adapter (4) onto the va-

cuum cleaner connector (f). Connect the dust 

extractor adapter (4) to a suitable dust extraction 

system.

Important!

For health safety reasons it is imperative that you 

use a dust extraction system.

Important!

For health safety reasons it is imperative that 

you use the dust collection box.

5.3  Securing sanding/grinding paper using a 

clamp (Fig. 3-6)

Only use sanding/grinding paper of the appropria-

te size and suitable perforations.

• 

 Lift the lever (7) on the front of the orbital san-

der.

• 

 Insert the sanding/grinding paper as far as 

possible into the open clamp and close the 

lever again.

• 

 Place the sanding/grinding paper taut over 

the orbital plate (5) and clamp it again using 

the second lever (7) on the rear of the orbital 

sander.

• 

Make sure that the perforations in the san-

Anl_TE-OS_18_230_Li_Solo_SPK9.indb   18

Anl_TE-OS_18_230_Li_Solo_SPK9.indb   18

05.10.2020   11:04:32

05.10.2020   11:04:32