Bosch GWS 26 230 LVI - Инструкция по эксплуатации - Страница 14

14

 | English 

1 619 929 J75 | (26.10.11)

Bosch Power Tools

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the 

materials to be worked.

f

Prevent dust accumulation at the workplace. 

Dusts can 

easily ignite.

f

Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

f

After breakage of the grinding disc during operation or 

damage to the holding fixtures on the protection guard/ 

power tool, the machine must promptly be sent to an after-

sales service agent for maintenance for addresses, see 

section “After-sales Service and Customer Assistance”.

f

Adjust protection guard in such a manner that sparking 

toward the operator is prevented.

f

The tightening tension of the clamp from the protection 

guard can be changed by loosening or tightening the ad-

justment screw. Ensure that the protection guard is tightly 

seated and check regularly.

f

Do not touch grinding and cutting discs before they 

have cooled down. 

The discs can become very hot while 

working.

f

Actuate the spindle lock button only when the grinder 

spindle is at a standstill. 

Otherwise, the machine may be-

come damaged.

f

After mounting the grinding tool and before switching 

on, check that the grinding tool is correctly mounted 

and that it can turn freely. Make sure that the grinding 

tool does not graze against the protection guard or oth-

er parts.

f

When operating the machine with power from mobile gen-

erators, loss of performance or untypical behavior can oc-

cur upon switching on.

f

When the machine only runs with strongly reduced speed, 

the kickback stop has failed. When the machine runs at full 

speed immediately after switching on, the reduced start-

ing current, the restarting protection and the kickback 

stop have failed. The power tool should be sent immediate-

ly to an after-sales service (for addresses, see section “Af-

ter-sales Service and Customer Assistance”.

f

In case of short energy-containing pulses in the supply sys-

tem, which typically develop when lightning strikes, the 

power tool’s kickback stop may actuate. If so, the machine 

will switch off, yet can be restarted again thereafter imme-

diately.

f

When not using for extended periods, pull the mains plug 

out of the socket outlet. When the mains plug is inserted 

and mains voltage is given, the power tool, even when 

switched off, still consumes a low amount of current.

f

By applying too high application force, the machine can 

be subject to overload. Overload can lead to overheat-

ing and damage of the power tool. After heavily strain-

ing the power tool, continue to run it at no-load for sev-

eral minutes in order to cool it down.

f

Do not use the power tool with a cut-off stand.

f

Never use a cutting disc for roughing.

f

The quick-clamping nut may be used only for grinding 

or cutting discs. Use only a flawless, undamaged quick-

clamping nut.

f

When the damping element between main handle and 

motor housing is damaged, do not continue to use the 

power tool.

f

Do not continue to use the power tool when the auxilia-

ry handle is damaged. Do not make any changes or 

modifications to the auxiliary handle.

f

When rotating the main handle, always turn it through 

until it engages  –  see figure 9, page 235.

Products sold in GB only

: Your product is fitted with an 

BS 1363/A approved electric plug with internal fuse (ASTA 

approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be 

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should 

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible 

shock hazard and should never be inserted into a mains sock-

et elsewhere.

Products sold in AUS and NZ only

: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Symbols

The following symbols are important for reading and under-

standing the operating instructions. Please take note of the 

symbols and their meaning. The correct interpretation of the 

symbols will help you to use the machine in a better and safer 

manner.

Symbol

Meaning

Article number

Read all safety warnings and all instruc-

tions

Before any work on the machine itself, 

pull the mains plug from the socket out-

let

Wear protective gloves

Wear ear protection.

Wear safety glasses/goggles

OBJ_BUCH-1528-001.book  Page 14  Wednesday, October 26, 2011  8:25 AM