Bosch GGS 28 CE - Инструкция по эксплуатации - Страница 16

16

 | English 

3 609 929 C06 | (16.12.10)

Bosch Power Tools

g) If devices are provided for the connec-

tion of dust extraction and collection fa-
cilities, ensure these are connected and 
properly used. 

Use of dust collection can 

reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. 

The 

correct power tool will do the job better 
and safer at the rate for which it was de-
signed.

b) Do not use the power tool if the switch 

does not turn it on and off. 

Any power 

tool that cannot be controlled with the 
switch is dangerous and must be re-
paired.

c) Disconnect the plug from the power 

source and/or the battery pack from the 
power tool before making any adjust-
ments, changing accessories, or storing 
power tools. 

Such preventive safety 

measures reduce the risk of starting the 
power tool accidentally.

d) Store idle power tools out of the reach of 

children and do not allow persons unfa-
miliar with the power tool or these in-
structions to operate the power tool. 

Power tools are dangerous in the hands of 
untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts, 
breakage of parts and any other condi-
tion that may affect the power tool’s op-
eration. If damaged, have the power tool 
repaired before use. 

Many accidents are 

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. 

Prop-

erly maintained cutting tools with sharp 
cutting edges are less likely to bind and 
are easier to control.

g) Use the power tool, accessories and tool 

bits etc. in accordance with these in-
structions, taking into account the work-
ing conditions and the work to be per-
formed. 

Use of the power tool for 

operations different from those intended 
could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qual-

ified repair person using only identical 
replacement parts. 

This will ensure that 

the safety of the power tool is maintained.

Safety Warnings for Straight Grinders

Safety Warnings Common for Grinding, Wire 
Brushing, Polishing or Carving:

f

This power tool is intended to function as a 
grinder, carving tool, polisher (GGS 8 CE) 
or wire brush (GGS 8 CE). Read all safety 
warnings, instructions, illustrations and 
specifications provided with this power 
tool. 

Failure to follow all instructions listed 

below may result in electric shock, fire 
and/or serious injury.

f

Do not use accessories which are not spe-
cifically designed and recommended by the 
tool manufacturer. 

Just because the acces-

sory can be attached to your power tool, it 
does not assure safe operation.

f

The rated speed of the accessory must be at 
least equal to the maximum speed marked 
on the power tool. 

Accessories running fast-

er than their rated speed can break and fly 
apart.

f

The outside diameter and the thickness of 
your accessory must be within the capacity 
rating of your power tool. 

Incorrectly sized 

accessories cannot be adequately controlled.

f

The arbour size of wheels, sanding drum or 
any other accessory must properly fit the 
spindle or collet of the power tool. 

Accesso-

ries that do not match the mounting hard-
ware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss 
of control.

f

Mandrel mounted wheels, sanding drums, 
cutters or other accessories must be fully 
inserted into the collet or chuck. The “over-
hang” or the length of the mandrel from the 
wheel to the collet must be minimal. 

If the 

mandrel is insufficiently held and/or the 
overhang of the wheel is too long, the mount-
ed wheel may become loose and ejected at 
high velocity.

OBJ_BUCH-1269-003.book  Page 16  Thursday, December 16, 2010  4:05 PM