Bort BWS-18Li-125 - Инструкция по эксплуатации - Страница 11

11

• Maintain power tools . Check for misalignment or bind-

ing of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation . If

damaged, have the power tool repaired before use . Many 

accidents are caused by poorly maintained power tools .

• Keep cutting tools sharp and clean . Properly maintained 

cutting tools with sharp cutting edges are less likely to

bind and are easier to control .

• Use the power tool, accessories and tool bits etc . in ac-

cordance with these instructions, taking into account the 

working conditions and the work to be performed . Use

of the power tool for operations different from those in-

tended could result in a hazardous situation .

Battery tool use and care

• Recharge only with the charger specified by the manu-

facturer . A charger that is suitable for one type of battery 

pack may create a risk of fire when used with another 

battery pack .

• Use power tools only with specifically designated bat-

tery packs . Use of any other battery packs may create a 

risk of injury and fire .

• When battery pack is not in use, keep it away from other 

metal objects, like paper clips, coins, keys, nails, screws 

or other small metal objects, that can make a connec-

tion from one terminal to another . Shorting the battery 

terminals together may cause burns or a fire .

• Under abusive conditions, liquid may be ejected from 

the battery; avoid contact . If contact accidentally occurs, 

flush with water . If liquid contacts eyes, additionally seek 

medical help . Liquid ejected from the battery may cause 

irritation or burns .

Service

Have your power tool serviced by a qualified repair person 

using only identical replacement parts . This will ensure that 

the safety of the power tool is maintained .

SAFETY WARNINGS FOR ANGLE GRINDER

• This power tool is intended to function as a grinder, sand-

er, wire brush or cut-off tool . Read all safety warnings, in-

structions, illustrations and specifications provided with 

this power tool . Failure to follow all instructions listed be-

low may result in electric shock, fire and/or serious injury .

• Operations such as polishing are not recommended to

be performed with this power tool . Operations for which 

the power tool was not designed may create a hazard

and cause personal injury .

• Do not use accessories which are not specifically de-

signed and recommended by the tool manufacturer . Just 

because the accessory can be attached to your power

tool, it does not assure safe operation .

• The rated speed of the accessory must be at least equal 

to the maximum speed marked on the power tool . Ac-

cessories running faster than their rated speed can break 

and fly apart .

• The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power

tool . Incorrectly sized accessories cannot be adequately

guarded or controlled .

• Threaded mounting of accessories must match the

grinder spindle thread . For accessories mounted by

flanges, the arbour hole of the accessory must fit the

locating diameter of the flange . Accessories that do not 

match the mounting hardware of the power tool will run 

out of balance, vibrate excessively and may cause loss of 

control .

• Do not use a damaged accessory . Before each use in-

spect the accessory such as abrasive wheels for chips and 

cracks, backing pad for cracks, tear or excess wear, wire

brush for loose or cracked wires . If power tool or acces-

sory is dropped, inspect for damage or install an undam-

aged accessory . After inspecting and installing an acces-

sory, position yourself and bystanders away from the

plane of the rotating accessory and run the power tool at 

maximum no-load speed for one minute . Damaged ac-

cessories will normally break apart during this test time .

• Wear personal protective equipment . Depending on ap-

plication, use face shield, safety goggles or safety glasses . 

As appropriate, wear dust mask, hearing protectors,

gloves and shop apron capable of stopping small abra-

sive or workpiece fragments . The eye protection must be 

capable of stopping flying debris generated by various

operations . The dust mask or respirator must be capable 

of filtrating particles generated by your operation . Pro-

longed exposure to high intensity noise may cause hear-

ing loss .

• Keep bystanders a safe distance away from work area . 

Anyone entering the work area must wear personal

protective equipment . Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond 

immediate area of operation .

• Hold the power tool by insulated gripping surfaces only, 

when performing an operation where the cutting acces-

sory may contact hidden wiring or its own cord . Cutting 

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock .

• Position the cord clear of the spinning accessory . If you

lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning wheel .

• Never lay the power tool down until the accessory has

come to a complete stop . The spinning wheel may grab 

the surface and pull the power tool out of your control .

• Do not run the power tool while carrying it at your side . 

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body .

• Regularly clean the power tool’s air vents . The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards .

• Do not operate the power tool near flammable materials . 

Sparks could ignite these materials .

• Do not use accessories that require liquid coolants . Using 

water or other liquid coolants may result in electrocution 

or shock .

SAFETY WARNINGS FO BATTERY TOOL

• Use auxiliary handle(s), if supplied with the tool . Loss of 

control can cause personal injury .

• Hold power tool by insulated gripping surfaces, when 

performing an operation where the cutting accessory 

may contact hidden wiring or its own cord . Cutting 

accessory contacting a “live” wire may make exposed 

metal parts of the power tool “live” and could give the 

operator an electric shock .