AEG WS13-125XE - Инструкция по эксплуатации - Страница 17

15

GB

English

e)  The outside diameter and the thickness of your 

accessory must be within the capacity rating of your power 

tool. 

Incorrectly sized accessories cannot be adequately guarded 

or controlled.

f)  Threaded mounting of accessories must match the grin-

der spindle thread. For accessories mounted by flanges, the 

arbour hole of the accessory must fit the locating diameter 

of the flange. 

Accessories that do not match the mounting hard-

ware of the power tool will run out of balance, vibrate excessively 

and may cause loss of control.

g)  Do not use a damaged accessory. Before each use inspect 

the accessory such as abrasive wheels for chips and cracks, 

backing pad for cracks, tear or excess wear, wire brush for 

loose or cracked wires. If power tool or accessory is dropped, 

inspect for damage or install an undamaged accessory. After 

inspecting and installing an accessory, position yourself and 

bystanders away from the plane of the rotating accessory 

and run the power tool at maximum no-load speed for one 

minute. 

Damaged accessories will normally break apart during this 

test time.

h)  Wear personal protective equipment. Depending on 

application, use face shield, safety goggles or safety glasses. 

As appropriate, wear dust mask, hearing protectors, gloves 

and shop apron capable of stopping small abrasive or 

workpiece fragments.

 The eye protection must be capable of 

stopping flying debris generated by various operations. The dust 

mask or respirator must be capable of filtrating particles generated 

by your operation. Prolonged exposure to high intensity noise may 

cause hearing loss.

i)  Keep bystanders a safe distance away from work area. 

Anyone entering the work area must wear personal protec-

tive equipment. 

Fragments of workpiece or of a broken accessory 

may fly away and cause injury beyond immediate area of operation.

j)  Hold the power tool by insulated gripping surfaces only, 

when performing an operation where the cutting accessory 

may contact hidden wiring or its own cord.

 Cutting accessory 

contacting a „live“ wire may make exposed metal parts of the power 

tool „live“ and could give the operator an electric shock.

k)  Position the cord clear of the spinning accessory.

  If you lose 

control, the cord may be cut or snagged and your hand or arm may be 

pulled into the spinning wheel.

l)  Never lay the power tool down until the accessory has 

come to a complete stop. 

The spinning accessory may grab the 

surface and pull the power tool out of your control.

m)  Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag your 

clothing, pulling the accessory into your body.

n)  Regularly clean the power tool’s air vents. 

The motor’s fan 

will draw the dust inside the housing and excessive accumulation of 

powdered metal may cause electrical hazards.

o)  Do not operate the power tool near flammable materials.

Sparks could ignite these materials.

p)  Do not use accessories that require liquid coolants.

 Using 

water or other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating 

wheel, backing pad, brush or any other accessory. Pinching or snag-

ging causes rapid stalling of the rotating accessory which in turn 

causes the uncontrolled power tool to be forced in the direction 

opposite of the accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the 

workpiece, the edge of the wheel that is entering into the pinch 

point can dig into the surface of the material causing the wheel 

to climb out or kick out. The wheel may either jump toward or 

away from the operator, depending on direction of the wheel’s 

movement at the point of pinching. Abrasive wheels may also break 

under these conditions.
Kickback is the result of power tool misuse and/or incorrect opera-

ting procedures or conditions and can be avoided by taking proper 

precautions as given below.

a)  Maintain a firm grip on the power tool and position your 

body and arm to allow you to resist kickback forces. Always 

use auxiliary handle, if provided, for maximum control over 

kickback or torque reaction during start-up. 

The operator can 

control torque reactions or kickback forces, if proper precautions 

are taken.

b)  Never place your hand near the rotating accessory. 

Accessory may kickback over your hand.

c)  Do not position your body in the area where power tool 

will move if kickback occurs. 

Kickback will propel the tool in 

direction opposite to the wheel’s movement at the point of snagging.

d)  Use special care when working corners, sharp edges etc. 

Avoid bouncing and snagging the accessory. 

Corners, sharp 

edges or bouncing have a tendency to snag the rotating accessory 

and cause loss of control or kickback.

e)  Do not attach a saw chain woodcarving blade or toothed 

saw blade. 

Such blades create frequent kickback and loss of control.

Safety Warnings Specific for Grinding and Abrasive Cutting-

Off Operations:
a)  Use only wheel types that are recommended for your 

power tool and the specific guard designed for the selected 

wheel. 

Wheels for which the power tool was not designed cannot be 

adequately guarded and are unsafe.

b)  The guard must be securely attached to the power tool 

and positioned for maximum safety, so the least amount 

of wheel is exposed towards the operator. 

The guard helps 

to protect the operator from broken wheel fragments, accidental 

contact with wheel and sparks that could ignite clothing.

c)  Wheels must be used only for recommended applications. 

For example: do not grind with the side of cut-off wheel.

 Abra-

sive cut-off wheels are intended for peripheral grinding, side forces 

applied to these wheels may cause them to shatter.

d)  Always use undamaged wheel flanges that are of correct 

size and shape for your selected wheel. 

Proper wheel flanges 

support the wheel thus reducing the possibility of wheel breakage. 

Flanges for cut-off wheels may be different from grinding wheel 

flanges.

e)  Do not use worn down wheels from larger power tools. 

Wheel intended for larger power tool is not suitable for the higher 

speed of a smaller tool and may burst.

Additional Safety Warnings Specific for Abrasive Cutting-Off 

Operations:
a)  Do not “jam” the cut-off wheel or apply excessive pressure. 

Do not attempt to make an excessive depth of cut. 

Overstressing 

the wheel increases the loading and susceptibility to twisting or