AEG WS10-125 - Инструкция по эксплуатации - Страница 20

18

GB

English

Safety Warnings Specific for Wire Brushing Operations:
a)  Be aware that wire bristles are thrown by the brush 

even during ordinary operation. Do not overstress the wires 

by applying excessive load to the brush. 

The wire bristles can 

easily penetrate light clothing and/or skin.

b)  If the use of a guard is recommended for wire brushing, 

do not allow any interference of the wire wheel or brush 

with the guard.

 Wire wheel or brush may expand in diameter due 

to work load and centrifugal forces.

Additional Safety and Working Instructions

When grinding metal, flying sparks are produced. Take care that 

no persons are endangered. Because of the danger of fire, no 

combustible materials should be located in the vicinity (spark flight 

zone). Do not use dust extraction.
Avoid flying sparks and sanding dust hit your body.
Never reach into the danger area of the machine when it is running.
Immediately switch off the machine in case of considerable vibra-

tions or if other malfunctions occur. Check the machine in order to 

find out the cause. 
Under extreme conditions (e.g. smooth-grinding metals with 

the arbour and vulcanized fibre grinding disk), significant 

contamination can build up on the inside of the angle grinder. For 

safety reasons, in such conditions a ground fault interrupter must 

be connected in series. If the ground fault interrupter trips the 

machine must be sent for service.
Chips and splinters must not be removed while the machine is 

running.

MAINS CONNEC TION

Connect only to single-phase AC system voltage as indicated on 

the rating plate. It is also possible to connect to sockets without an 

earthing contact as the design conforms to safety class II.
Appliances used at many different locations including wet room 

and open air must be connected via a residual current device (FI, 

RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched off.
Do not let any metal parts enter the airing slots - danger of short 

circuit!
Inrush currents cause short-time voltage drops. Under unfavoura-

ble power supply conditions, other equipment may be affected. If 

the system impedance of the power supply is lower than 0,2 Ohm, 

disturbances are unlikely to occur.

SPECIFIED CONDITIONS OF USE

The angle grinder is intended for grinding and cutting metal, stone 

and ceramic materials as well as sanding and wire brushing.
Use the cutting guard from the accessories range for cutting 

application.
Please refer to the instructions supplied by the accessory 

manufacturer.
The machine is suitable only for working without water.

WORKING INSTRUC TIONS

For accessories intended to be fitted with threaded hole wheel, 

ensure that the thread in the wheel is long enough to accept the 

spindle length.
Always use and store the cutting and grinding disks according to 

the manufacturer‘s instructions.
Always use the correct guard for cutting and grinding.
The grinding surface of the centre depressed disks must be moun-

ted min. 2 mm below the plane of the guard lip. 
The adjusting nut must be tightened before starting to work with 

the machine.
Always use the auxiliary handle.
The workpiece must be fixed if it is not heavy enough to be steady. 

Never move the workpiece towards the rotating disk by hand.  

The flange nut must be securely tightened before the machine is 

started. 

If the tool is not securely tightened with the flange nut, it is pos-

sible that the tool will lose the required clamping force when it is 

decelerated. 

In the event that a power failure occurs whilst the machine is 

operating, the brake function will be inoperative.

ELEC TRONICS

Machines with a lockable switch are supplied with a restart cutout. 

This prevents the machine restarting by itself after a power failure. 

When resuming work, switch the machine off and then switch it 

back on again.
The device has an overload protection function and will stop if an 

overload occurs. Machine shut-off. After the machine has cooled 

down the device can be put back into operation.

SMOOTH START

Electronic smooth start for save use prevents jerky run-up of the 

machine.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
If the supply cord of this power tool is damaged, it must be 

replaced by a specially prepared cord available through the service 

organization.
Use only AEG accessories and spare parts. Should components need to 

be replaced which have not been described, please contact one of our 

AEG service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state 

the Article No. as well as the machine type printed on the label 

and order the drawing at your local service agents or directly at: 

Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnen-

den, Germany.