Ryobi R18RS-0 (5133002637) - Инструкция по эксплуатации - Страница 4

OPERATION TIPS

 WARNING

Be careful not to twist or bend the saw blade.

■

Do not force the product.

■

Use cutting oil when cutting soft metals and steel. 
Cutting oil also keeps the blades cool, increases cutting 
action, and prolongs blade life.

■

Clamp the workpiece firmly and cut close to the 
clamping point to eliminate any vibration of the work. 
When cutting conduit pipe or angle iron, secure the 
workpiece with a vise, if possible, and cut close to the 
vise. To cut a thin-sheet material, place the material 
between two hardboards or plywood and clamp the 
layers to eliminate vibration and material tearing.

■

Always keep a firm forward pressure on the tool to keep 
the shoe in contact with the workpiece.

■

Do not use cracked or distorted saw blades. Do not use 
saw blades that are damaged or deformed.

 WARNING

Dust from certain paints, coatings, and materials may 
cause irritation or allergic reactions. Dust from wood 
such as oak, beech, MDF, and others are carcinogenic. 
Materials containing asbestos should only be worked on 
or processed by quali

fi

 ed specialist operators.

 WARNING

Always wear safety goggles or safety glasses with 
side shields when operating the product. Failure to do 
so could result in objects being thrown into your eyes 
resulting in possible serious injury.

MAINTENANCE

 WARNING

The product should never be connected to a power 
supply when assembling parts, making adjustments, 
cleaning, performing maintenance, or when the product 
is not in use. Disconnecting the product will prevent 
accidental starting that could cause serious injury.

■

When servicing, use only identical replacement parts. 
Use of any other parts may create a hazard or cause 
product damage.

■

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to various types of commercial 
solvents and may be damaged by their use. Use clean 
cloths to remove dirt and carbon dust.

■

Do not, at any time, let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact 
with plastic parts. They contain chemicals that can 
damage, weaken, or destroy plastic.

■

Always wear safety goggles or safety glasses with side 

shields during power tool operation or when blowing 
dust. If operation is dusty, also wear a dust mask.

■

For greater safety and reliability, all repairs should be 
performed by an authorised service centre.

GENERAL

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to various types of commercial 
solvents and may be damaged by their use. Use clean 
cloths to remove dirt, carbon dust, etc.
Electrical tools used on 

fi

 berglass material, wallboard, 

spackling compounds, or plaster are subject to accelerated 
wear and possible premature failure because the 

fi

 berglass 

chips and grindings are highly abrasive to bearings, 
brushes, and commutators. We do not recommend using 
the product for extended periods of time on these types 
of materials.

 WARNING

Do not use compressed air to blow dust from the product. 
This practice is dangerous and can cause dirt and grit to 
be blasted into someone’s eyes, causing injury.

LUBRICATION

All of the bearings in the product are lubricated with a 
suf

fi

 cient amount of high grade lubricant for the life span of 

the product under normal operating conditions. Therefore, 
no further lubrication is required.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 
of as waste. The machine, accessories, and 
packaging should be sorted for environment-
friendly recycling.

SYMBOLS ON THE PRODUCT

Safety Alert

No-load speed

V

Volts
Direct current

min

-1

Revolutions or reciprocations per minute

CE Conformity

EurAsian Conformity Mark

Ukrainian mark of conformity

Please read the instructions carefully before 
starting the product.

2

| English