Makita JR3061T - Инструкция по эксплуатации - Страница 5

5 ENGLISH

Recipro saw safety warnings

1. 

Hold the power tool by insulated gripping 

surfaces, when performing an operation where 

the cutting accessory may contact hidden wir-

ing or its own cord.

 Cutting accessory contacting 

a "live" wire may make exposed metal parts of the 

power tool "live" and could give the operator an 

electric shock.

2. 

Use clamps or another practical way to secure 

and support the workpiece to a stable plat-

form.

 Holding the workpiece by hand or against 

your body leaves it unstable and may lead to loss 

of control.

3. 

Always use safety glasses or goggles. 

Ordinary eye or sun glasses are NOT safety 

glasses.

4. 

Avoid cutting nails. Inspect workpiece for any 

nails and remove them before operation.

5. 

Do not cut oversize workpiece.

6. 

Check for the proper clearance beyond the 

workpiece before cutting so that the blade will 

not strike the floor, workbench, etc.

7. 

Hold the tool firmly.

8. 

Make sure the blade is not contacting the 

workpiece before the switch is turned on.

9. 

Keep hands away from moving parts.

10. 

Do not leave the tool running. Operate the tool 

only when hand-held.

11. 

Always switch off and wait for the blade to 

come to a complete stop before removing the 

blade from the workpiece.

12. 

Do not touch the blade or the workpiece imme-

diately after operation; they may be extremely 

hot and could burn your skin.

13. 

Do not operate the tool at no-load 

unnecessarily.

14. 

Always use the correct dust mask/respirator 

for the material and application you are work-

ing with.

15. 

Some material contains chemicals which may 

be toxic. Take caution to prevent dust inhala

-

tion and skin contact. Follow material supplier 

safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

Always be sure that the tool is 

switched off and unplugged before adjusting or 

checking function on the tool.

Switch action

WARNING:

Before plugging in the tool, 

always check to see that the switch trigger actu-

ates properly and returns to the "OFF" position 

when released.

WARNING:

Switch can be locked in "ON" 

position for ease of operator comfort during 

extended use. Apply caution when locking tool in 

"ON" position and maintain firm grasp on tool.

CAUTION:

Return the switch trigger to the 

"OFF" position in case of accidental unplugging, 

blackout, or the power is cut unintentionally.

Otherwise the tool may start suddenly when the 

power returns and it may result in personal injury.

To start the tool, simply pull the switch trigger. Tool 

speed is increased by increasing pressure on the switch 

trigger. Release the switch trigger to stop.

For continuous operation, pull the switch trigger and then 

push in the lock button. To stop the tool from the locked 

position, pull the switch trigger fully, then release it.

► 

Fig.1:

1.

 Switch trigger 

2.

 Lock button

Adjusting the shoe

When the recipro saw blade loses its cutting efficiency 

in one place along its cutting edge, reposition the shoe 

to utilize a sharp, unused portion of its cutting edge. This 

will help to lengthen the life of the recipro saw blade.

The position of the shoe can be adjusted in five levels.

To reposition the shoe, open the shoe adjusting lever and 

select the suitable position, then close the shoe adjusting lever.

► 

Fig.2:

1.

 Shoe 

2.

 Shoe adjusting lever

NOTICE:

The shoe cannot be secured if 

it is extended more than the   marking 

of 

 stamping. Do not close the shoe 

adjusting lever forcibly in such a position.

 It may 

result in breakage of the lever.

NOTE:

 The shoe cannot be adjusted without opening 

the shoe adjusting lever fully.

Lighting up the front lamp

► 

Fig.3:

1.

 Lamp

CAUTION:

Do not look in the light or see the 

source of light directly.

To turn on the lamp, pull the switch trigger. Release the 

switch trigger to turn it off.

NOTE:

 Use a dry cloth to wipe the dirt off the lens of 

the lamp. Be careful not to scratch the lens of lamp, or 

it may lower the illumination.