Vaddio EasyIP Switch (999-11208-001) - Инструкция по эксплуатации - Страница 5

Fold

Fold

Fold

3

 Preparing for Access

IP Addressing

If the AMS-1208P is connected to a network with a 192.168.0.X address 

scheme, and your computer shares a similar address on the same network, 
you can skip to the next step, 

Access and Setup

.

n

Note:

   If another device on your network shares the 192.168.0.3 

address, you’ll need to temporarily reassign or remove that 
device while you configure the AMS-1208P.

If your network uses an address scheme other than 192.168.0.X, you’ll need 
to set a temporary static IP address on the computer you’re using for 

configuration. To do so, set the IP address of your computer to an address 
in the 192.168.0.X range, then set the Gateway/Router address to 192.168.0.3 

(the default IP address of the AMS-1208P).

Once you’re finished configuring the switch, you can return your comput-

er’s IP configuration to normal, typically “Obtain Automatically/DHCP.”

n

Note:

    Visit 

http://luxul.com/ip-addressing

 to learn more about 

changing your computer’s IP address and getting connected.

4

Access and Setup

Getting Connected

Use an Ethernet cable to connect your computer to the AMS-1208P, then 
power on the switch.

Logging In

To access the AMS-1208P web configuration, open your web browser and  

enter the switch’s default 192.168.0.3 IP address in the address field. Log in to  
the switch using the default user name and password:

Default IP:  192.168.0.3

Username:  admin

Password:  admin

Select the menu items on the left to view and/or modify the configuration. 

5

Hardware Operation

Front Panel

The front panel of the AMS-1208P includes Power, System, PoE and Link/

Activity indicators, as well as 12 port status indicators.

AMS-1208P Front Panel View

Rear Panel

The rear panel of the AMS-1208P Switch includes 1 console port, 10 Gigabit RJ-45 

ports and 2 Gigabit SFP ports, as well as LED status indicators for each port. A 

mode/reset button switches the display between Link/Activity and PoE modes, 

while the Blue/Green toggle switches the front-panel LED indicator color.

AMS-1208P Rear Panel View

LED Indicators

The LED indicators on the AMS-1208P include System, Link/Act and PoE LEDs, 
and an LED for each port. These LED indicators show the operating status of 

the AMS-1208P and each port connection.

Mode/Reset Button to Change LED Functionality

Tapping the Mode/Reset button briefly switches the port indicators between 
displaying port link speed and PoE status.

The following chart shows the LED indicators of the AMS-1208P along with an 

explanation of the indicator’s properties:

Indicator 
Name

Description

Power

On

Power is applied to the AMS-1208P.

Off

Power is disconnected or power switch 
off.

System

Flashing

Indicates normal operation.

On

Indicates a malfunction. Contact support.

Off

Indicates startup/initialization process or 
that power is not on.

Port Link/
Act Status 
1-12

Green

1000Mbps device connected to the port.

Yellow

10/100Mbps device connected to the port.

Flashing

Port receiving or transmitting data.

Off

Nothing connected to the port.

Port PoE 
Status 1-8

Green

Switch is providing PoE power to a device.

Yellow

PoE is off due to a fault or because the 
connected device is exceeding power limit.

Off

Port disconnected or link failed.

Note: At startup, the port LEDs will flash briefly during a self-test.

Mode/Reset Button to Reset/Restore

The Reset button (located at the lower-left corner of the rear panel) is  
used to reset (reboot) the switch, or to restore the switch to factory  
default settings.

X

To Reboot/Reset the Switch:

 With the AMS-1208P powered on, press 

the Reset button for approximately three seconds until the Link/Act and 

PoE LEDs both light, then release the button.

c

CAUTION:

    Do not hold the button for more than four seconds. 

Doing so could erase all settings and restore  

factory defaults.

X

To Restore Default Settings:

 With the AMS-1208P powered on, press 

and hold the Reset button approximately eight seconds, until both the 
Link/Act and PoE LEDs turn off, then release the Reset button and the 
switch automatically restores factory default settings and reboots. Once 
the System LED starts flashing again, the AMS-1208P is running with 
factory defaults.

c

CAUTION:

   Please note that restoring Default Settings will remove 

any/all custom configuration.