Vaddio EasyIP Switch (999-11208-001) - Инструкция по эксплуатации - Страница 3

Fold

Fold

Fold

RE

AD 
ME 
FIRS

T

QUICK INSTALL GUIDE

AV Series  

12-Port/8 PoE+ Gigabit  

Managed Switch 

AMS-1208P

Includes:

„

AMS-1208P 12-Port/8 PoE+ Switch

    (Includes Rack Mount Kit and Power Cord)

INSTALLATION AND SETUP

1

Physical Installation

The AMS-1208P can easily be installed in a standard 19” rack. Two mounting ears 

are included for installing and stabilizing the switch. When attaching the mounting 
ears and installing the switch in a rack, please refer to the following illustration:

Rack-Mounting the AMS-1208P

„

 Use the included screws to attach the mounting ears to each side  

of the switch.

„

 Mount the switch in the rack with the LEDs facing outwards. Be sure the 
switch is level and properly secured in the rack. 

Desktop Setup

For use as a desktop device, position and apply the included rubber feet to the 
bottom of the AMS-1208P. 

2

Connecting Ethernet and Power

Ethernet and Power Connections

Use one of the ten Ethernet ports to connect the AMS-1208P to any Ethernet-
enabled device, including servers, routers or other switches.  No crossover cable 
is necessary. 

The AMS-1208P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode. Ports 1-8 are PoE+ and 
are enabled by default. Ports 9 and 10 are Gigabit Ethernet only (non PoE), 

while ports 11 and 12 are Gigabit SFP ports.

Use the included power cable to connect the AMS-1208P to a surge- 
protected outlet. The AC input socket is on the rear panel. The built-in 
power supply supports 100~240VAC at 50/60Hz.

Network Cabling

Luxul recommends Category-5, super Category-5 or Category-6 unshielded 
twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best performance and 

stable data transmission at 1000 Mbps, use Category-6 shielded twisted pair. 

If you intended to use optical fiber to extend the network beyond the 300-
foot limit of twisted pair Ethernet, SFP modules are required (not included). 

c

CAUTION:

  Multiple Uplink channels can create loops, resulting in 

network failure. Ensure only one Uplink channel exists 

between switches or between the AMS-1208P and a router.

n

NOTE:

  When powering up, the port LEDs may take a moment to 

initialize. This is normal as the AMS-1208P initialization and 
startup sequence completes.

n

NOTE:

  The AMS-1208P has an internal 130W power supply. Do not 

exceed 25.5W each or 130W combined consumption of all 

external PoE devices.

Sales

P: 801-822-5450 

E: sales@luxul.com

Technical Support

P: 801-822-5450 Option 3 

E: support@luxul.com

LUX-QIG-AMS-1208P-v3 01251709

Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission 

in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves 

the right to make changes to any product to improve reliability, function, or design. No license is granted, 

either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied 

license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and 

Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other 

trademarks and registered trademarks are property of their respective holders.