ProfiCare PC-BSR 3043 - Инструкция по эксплуатации - Страница 56

PC-BSR3043_IM 

10.07.19

56

  WARNING: 

•  Under no circumstances should you immerse the appliance in 

water for cleaning purposes. Otherwise this might result in an 

electric shock or fire.

  CAUTION:

•  Do not use a wire brush or any abrasive items.

•  Do not use any acidic or abrasive detergents.

  NOTE:

Do not attempt to lubricate the rollers with lubricants or oil. 

Ignoring this would cause significantly more dust or dirt to 

adhere to the rollers.

•  Clean the housing with a soft, dry cloth without additives.

•  Use a soft cloth to gently clean the sensors (15/18/24). 

  CAUTION:

Prior to and after each use, check that the sensors are 

clean. Otherwise, the appliance may tumble down a 

staircase.

•  Prior to and after each use, make sure that the nozzle 

and vents are clear.

•  For optimum performance of the appliance, you should 

empty the dust container and clean the filters after each 

use.

Emptying the Dust Container and Cleaning the Filter 

  CAUTION:

Never wash the filters under any circumstances.

1.  Open the dust container compart-

ment by using the tab to pull up the 

cover.

2.  Reach into the recesses and 

pull the dust container out of the 

appliance.

3.  Fold the cover of the dust container 

upwards.

4.  Empty the dust container while holding it 

over a garbage can. 

5. 

Pull the HEPA filter out of the dust 

container. There is still a fitting for 

the HEPA filter in the dust container. 

Gently push it towards the outside. 

Clean the HEPA filter and its fitting by 

carefully beating it.

We recommend replacing the HEPA 

filter once a year.

  CAUTION:

Do not

 use a brush to clean the HEPA filter. Using a 

brush may damage the filter material.

6.  You can clean the dust container under running water. 

Use a soft brush to clean the 

fitting

.

  CAUTION:

•  Allow the dust container to air dry. Do not, however, 

expose it to direct sunlight.

• 

Only re-insert the filters into the dust container once 

it is completely dry!

7. 

Reinsert the filters into the dust container. Make sure 

that both the 

fitting

 and the 

HEPA filter

 are inserted 

correctly.

8.  Put the dust container back into the appliance. It must 

audibly engage.

Cleaning / Replacing the Side Brushes
If the side brushes are dirty, you may clean them with clean 

water. Do not use any additional cleaning agents.
If the side brushes are worn or defective, replace them with 

new ones.
1.  Turn the appliance upside down. Make sure that the 

cover of the dust container compartment does not open 

while performing this step.

  NOTE:

The cover is kept closed only by its own weight.

2.  Use a suitable Phillips screwdriver to unscrew the screw 

anticlockwise and remove it. 

3.  Pull the side brush upwards.

-  Clean the side brush of hair or other debris. Put the 

side brush back on and use the screw to remount it. 

Use a screwdriver to tighten the screw by hand.

or
-  Now, put the new side brush back on and use the 

screw to remount it. Use a screwdriver to tighten the 

screw by hand.

Cleaning the Floor Brush

For easy cleaning, the floor brush can be removed.  

1.  Remove the cover by pressing 

the latches (a) and at the same 

time pulling the cover upwards.

2. 

Pull the floor brush on the side 

with the rubber mount upwards 

and out of the appliance.