Skil 1470 - Инструкция по эксплуатации - Страница 9

9

- 

check the tight seating of the accessory

 (incorrect 

or not securely fastened accessories can come loose 

during operation and create a hazard)

•  Mounting of sanding sheet 

6

-  knock the dust out of the VELCRO material on sanding 

pad C 

2

 before mounting the sanding sheet

-  mount VELCRO sanding sheet as illustrated

!  the dust suction requires the use of perforated 

sanding sheets

!  perforation in sanding sheet should correspond 

with perforation in sanding foot

!  replace worn sanding sheets in time

!  always use the tool with the total VeLCrO 

surface covered with sanding paper

•  Dust/chip extraction 

7

-  mount dust extraction device D as illustrated

-  connect vacuum cleaner

!  do not use dust extraction device/vacuum cleaner 

when sanding metal

-  clean dust extraction device D regularly for optimal 

dust pick-up performance

•  On/off

-  switch on/off the tool by pushing switch E 

2

 in “I”/”O” 

position

!  before the accessory reaches the workpiece, the 

tool should run at full speed

!  before switching off the tool, you should lift it 

from the workpiece

•  Adjusting working speed 

8

-  with wheel F the required oscillating frequency can be 

adjusted from low (1) to high (6) (also while tool is 

running)

-  the optimal working speed depends on the material 

and can be determined with practical trials

•  Holding and guiding the tool

!  while working, always hold the tool at the 

grey-coloured grip area(s) 

9

-  keep ventilation slots G 

2

 uncovered

-  do not apply too much presssure on the tool 

(excessive pressure will cause excessive heat and 

may shorten the service life of the accessory)

•  Depth adjustment accessory (DEPTH STOP) (

not 

standard included

) 

0

aPPLICaTION adVICe

•  Use segment saw blade H 

2

 for separating and plunge 

cuts in wood, plaster, gypsum and plastics (also for 

sawing close to edges, in corners and other hard-to-

reach areas)

•  Use plunge-cut saw blade J 

2

 for separating and deep 

plunge-cuts in wood, plaster, gypsum and soft plastics 

(also for sawing close to edges, in corners and other 

hard-to-reach areas)

•  For more tips see www.skil.com

MaINTeNaNCe / serVICe

•  This tool is not intended for professional use

•  Always keep tool and cord clean (especially ventilation 

slots G 

2

)

!  disconnect the plug before cleaning

•  If the tool should fail despite the care taken in 

manufacturing and testing procedures, repair should be 

carried out by an after-sales service centre for SKIL 

power tools

-  send the tool 

undismantled

 together with proof of 

purchase to your dealer or the nearest SKIL service 

station (addresses as well as the service diagram of 

the tool are listed on www.skil.com)

eNVIrONMeNT

• 

do not dispose of electric tools, accessories and 

packaging together with household waste material

(only for EU countries)

-  in observance of European Directive 2012/19/EC on 

waste of electric and electronic equipment and its 

implementation in accordance with national law, 

electric tools that have reached the end of their life 

must be collected separately and returned to an 

environmentally compatible recycling facility

-  symbol 

!

 will remind you of this when the need for 

disposing occurs

deCLaraTION OF CONFOrMITY 

Multifunction tool 1470

Technical data 

1

•  We declare under our sole responsibility that the product 

described under “Technical data” is in conformity with the 

following standards or standardization documents: EN 

60745, EN 61000, EN 55014, in accordance with the 

provisions of the directives 2014/30/EU, 2006/42/EC, 

2011/65/EU

• 

Technical file at

: SKIL Europe BV (PT-SEU/ENG1), 

4825 BD Breda, NL

¹ÊÁÂÆιƼ½ÊÇǾ¼½Æ

ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿

ÍÊÇȽƓˁ˅ʿ˂ ʽ¼¹Ɠ

Ĺ¾ ÁÂÿʹ¹¾

ÈÈÊÇιĹƹ¿½Ê

29.07.2014

NOIse/VIBraTION

•  Measured in accordance with EN 60745 the sound 

pressure level of this tool is 92 dB(A) and the sound 

power level 103 dB(A) (standard deviation: 3 dB), and the 

vibration 

✱

 (triax vector sum; uncertainty K = 1.5 m/s²)

✱

 when sanding 8.8 m/s²

✱

 when cutting with plunge-cut saw blade 13.9 m/s²

✱

 when cutting with segment saw blade 7.2 m/s²

•  The vibration emission level has been measured in 

accordance with a standardised test given in EN 60745; it 

may be used to compare one tool with another and as a 

preliminary assessment of exposure to vibration when 

using the tool for the applications mentioned

-  using the tool for different applications, or with different 

or poorly maintained accessories, may significantly 

increase

 the exposure level