Ryobi R18MT3-0 - Инструкция по эксплуатации - Страница 4

or tape. Do not transport batteries that are cracked or 

leaking. Check with the forwarding company for further 

advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 

impossible to completely eliminate certain residual risk 

factors. The following hazards may arise and the operator 

should pay special attention to avoid the following:

■

Injury caused by dust

–

Wear eye protection at all times.

–

Wear respiratory protection masks containing filters 

appropriate to the materials being worked. Ensure 

adequate workplace ventilation.

–

Do not eat, drink or smoke in the work area.

■

Injury caused by noise and vibration

–

Wear ear protection.

–

Do not operate the product for long periods of time. 

See “Risk reduction”.

■

Risk of electrocution if electric cables are cut

–

Always hold the product by designated handles. Do 

not touch the cutting blades or metal parts of the 

product.

RISK REDUCTION

It has been reported that vibrations from handheld tools 

may contribute to a condition called Raynaud’s Syndrome 

in certain individuals. Symptoms may include tingling, 

numbness and blanching of the 

fi

 ngers, usually apparent 

upon exposure to cold. Hereditary factors, exposure to 

cold and dampness, diet, smoking, and work practices 

are all thought to contribute to the development of these 

symptoms. There are measures that can be taken by the 

operator to possibly reduce the effects of vibration:

■

Keep your body warm in cold weather. When operating 

the product, wear gloves to keep the hands and wrists 

warm. It is reported that cold weather is a major factor 

contributing to Raynaud’s Syndrome.

■

After each period of operation, exercise to increase 

blood circulation.

■

Take frequent work breaks. Limit the amount of 

exposure per day.

If you experience any of the symptoms of this condition, 

immediately discontinue use and see your doctor about 

these symptoms.

 WARNING

Injuries may be caused, or aggravated, by prolonged 

use of a tool. When using any tool for prolonged periods, 

ensure you take regular breaks.

KNOW YOUR PRODUCT

See page 105.

1. LED light
2.  Blade locking screw
3. Speed control
4.  On/ off switch
5.  Lock on switch
6.  Handle, insulated grasping surface

7.  Plunge cut blade
8.  Flush cut blade
9. Sanding pad
10. Sandpaper
11. Adaptor storage slot
12. Adaptor */**
13. Hex key
14. Battery port
*Compatible with BOSCH accessories. BOSCH is a 

registered trademark of Robert Bosch GmbH.

**Compatible with DREMEL accessories. DREMEL is a 

registered trademark of Robert Bosch Tool Corporation.

OPERATION

The product is supplied with an extra adapter for use with 

other brands of cutting, scraping, and sanding accessories. 

The adapter may be turned over for use with the desired 

brands of accessories. Do not use the adapter with RYOBI 

accessories supplied with your tool.

■

Secure workpieces that can move with a clamp to 

prevent movement during sanding or cutting operations. 

Do not hold the workpiece by hand. An inadvertent 

slip while operating the product may cause serious 

personal injury.

■

When making a plunge cut into soft materials like wood 

and plasterboard using the cutting accessory, gradually 

bring the vibrating blade to the workpiece. Do not push 

the vibrating blade hard into the material to be cut. Let 

the product do the work and concentrate on keeping the 

product and the cutting accessory stable in the position 

you wish to make the cut.

■

Take extra care when cutting in non-ferrous metals. 

The vibrating cutting blade may skip around before 

beginning the cut. If necessary, drill some holes along 

the line to be cut before you start cutting.

■

If the cutting accessories become jammed in the 

workpiece, switch off the product and disconnect from 

the power supply. If the cutting accessory cannot 

be removed easily, allow the cutting accessory to 

adequately cool before releasing the cutting accessory 

from the product. Wear gloves and use hand tools, such 

as pliers or wrench, to remove the cutting accessory 

from the workpiece.

OVERCURRENT PROTECTION

When overcurrent is detected, the product will automatically 

switch off.

If the product stops working, release the trigger and then 

apply again. The product should again start working.

MAINTENANCE

 WARNING

The product should never be connected to a power supply 

when you are assembling parts, making adjustments, 

cleaning, performing maintenance, or when the product 

is not in use. Disconnecting the product will prevent 

accidental starting that could cause serious injury.

■

When servicing, use only original manufacturer’s 

replacement parts. Use of any other parts may create a 

2

| English