Einhell TC-MG 220/1 E - Инструкция по эксплуатации - Страница 17

GB

- 17 -

Warning! 

Check that the plug-in tool is secure.

5.2 Triangular sanding/grinding plate

Fit the triangular sanding/grinding plate to use the 

equipment as a delta sander/grinder.

5.2.1 Fastening the sanding/grinding paper

The Velcro fastener enables easy changing of 

sanding/grinding paper. Make sure that the va-

cuum extraction holes on the sanding/grinding 

paper and the sanding/grinding disk are aligned.

5.3 Fitting the dust extraction device for the 

grinding/sanding plate (Fig. 3/4)

The dust extraction system prevents the accumu-

lation of dirt and high dust loads in the air, and it 

makes it easier to dispose of the dust.

• 

 Place the equipment in a stable position as 

shown in 5.1.

• 

 Fit the dust extraction device (6) with the tool 

mounting (2) positioned as shown in Figure 3.

• 

Secure the dust extraction device (6) by tigh-

tening the screw (7) with the Hexagon key 

(11).

• 

Make sure that the washer (4) is used for the 

screw (5) (see Figure 2). The camber on the 

washer must face upwards. 

• 

Place the triangular grinding/sanding plate 

on the dust extraction device (6) and the 

tool mounting (2) so that the pins of the tool 

mounting (2) fit into the recesses of the trian-

gular grinding/sanding plate (8), then fasten 

as shown in Fig. 4.

• 

 Connect your tool to an extraction unit or va-

cuum cleaner. This will provide excellent ext-

raction of chips and dust from the workpiece. 

The bene

fi

 ts are that you will protect both the 

equipment and your own health. Your work area 

will also be clean and safe.

6. Operation

 6.1 Switching on/o

ff

Slide the switch (1) forwards to switch on the 

equipment.

Slide the switch (1) to the rear to switch o

ff

  the 

equipment.

6.2 Practical tips

• 

 Switch on the equipment.

• 

 Work away from the body.

• 

 Never move your hands into the direct vicinity 

of the work area.

• 

 Use only plug-in tools which are in good wor-

king order and undamaged.

Plug-in tools

Sawing:

 Sawing wood and plastic. 

Notes on working practice: When sawing, watch 

out for foreign bodies in the workpiece and remo-

ve these if necessary. Plunge cutting is allowed 

only in soft materials such as wood or plaster-

board.

Sanding/grinding:

 Surface sanding/grinding at 

edges, in corners or hard-to-reach areas. Depen-

ding on choice of sanding/grinding paper for the 

sanding/grinding of wood, paint, lacquer, etc.

Notes on working practice: This equipment o

ff

 ers 

particularly high performance for the sanding/

grinding of hard-to-reach corners and edges. To 

sand/grind pro

fi

 les and channels you can also 

work with just the tip or the edge of the sanding/

grinding disk. Various sanding/grinding papers 

are available, specially designed for the di

ff

 erent 

types of material you may be working on and the 

amount you wish to remove from the surface. 

The amount removed will depend largely on the 

choice of sanding/grinding paper and pressure 

applied to the sanding/grinding disk.

Scraping:

 Scraping o

ff

  old paint or adhesives.

Notes on working practice: Move the plug-in tool 

against the area you want to remove. Begin with 

a 

fl

 at angle of incidence and little pressure. The 

surface (e.g. wood, plaster) may be damaged if 

too much pressure is used.

6.3 Speed control (Fig. 7)

You can select the speed by turning the speed 

controller (4).

Plus direction:  

Higher speed

Minus direction:  

Lower speed

7.  Replacing the power cable

Danger!

If the power cable for this equipment is damaged, 

it must be replaced by the manufacturer or its 

after-sales service or similarly trained personnel 

to avoid danger.

Anl_TC_MG_220_1_E_SPK9.indb   17

Anl_TC_MG_220_1_E_SPK9.indb   17

23.08.2017   08:10:41

23.08.2017   08:10:41