Пылесос VITEK VT-8149 (MC) - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.

5
ENGLISH
•
To wind the power cord (16), press the button (17),
hold the winding cord with your hand to avoid its
whipping and damage.
•
During the breaks you can place the brush (1) in the
horizontal brush storage (15).
Note: before replacing the brush (1) or the attach-
ments (29, 30) or cleaning the dust bin (11) switch the
vacuum cleaner off and take the power plug out of the
mains socket.
HEPA CLEANING SYSTEM
Cyclonic vacuum cleaner operates without dust bag.
Intake dirt is pushed into the dust bin by force of the
air flow. The air is cleaned with the reusable washable
HEPA filter (26) inside the dust bin, the motor protec-
tion filter (21) and the outlet air filter (18).
Attention!
Do not use the vacuum cleaner without the filter or if
the filter is damaged. The intake dust can get into the
unit and damage the motor.
Motor safety valve
The unit is equipped with the safety valve. If the dust
bin is full, the HEPA filter is blocked or the air vent is
blocked, the safety valve will switch on automatically
to prevent the motor overheating prolonging its ser-
vice life.
CLEANING AND CARE
Cleaning the dust bin (11)
Easy to clean the dust bin from garbage and dust.
Easy to control the filling of transparent dust bin.
In order to avoid foreign smell from dust and garbage it
is recommended to remove the dust and garbage from
the dust bin (11) after every room cleaning.
– Switch the vacuum cleaner off and unplug it.
– Holding the handle (13), press the release button
(25) and remove the dust bin (11) from the vacuum
cleaner body pulling upwards.
– Place the dust bin above the trash bin and press
the lid (28) lock button (22), the lid will open auto-
matically and you can remove the dust and garbage
from the dust bin (11).
– Close the lid (28) and make sure that it is fixed
properly.
– Install the dust bin (11) back to its place.
Cleaning the HEPA filter (26)
Regularly clean the HEPA filter (26) and the mesh fil-
ter (27). It’s better to clean them while cleaning the
dust bin.
– Remove the dust bin (11) from the vacuum cleaner
body as described in the previous chapter.
– Take the dust bin handle (23), carefully turn the lid
(24) counterclockwise and open the dust bin. Then
turn the HEPA filter counterclockwise and remove it
from the lid (24).
– Remove the mesh filter (27) from the HEPA filter (26).
– Now wash the HEPA filter, the mesh filter and the
dust bin intself under a warm water jet and let them
dry.
Attention!
– Wash the filter only with clean water, do not use
soap or detergent. It will damage the filter.
– Do not wash the filter in a dishwashing machine.
– Do not dry the HEPA filter with a hairdryer.
– Put the mesh filter (27) on the HEPA filter (26).
– Install the HEPA filter (26) back into the lid (24) and
turn it clockwise until clicking.
– Insert the lid (24) with the installed HEPA filter into
the dust bin (11) and turn it clockwise until it is fixed
properly. There are corresponding marks on the lid
and the container for proper installation.
Note: before installing the dust bin into the vacuum
cleaner body, check the condition of the motor
protection filter (21). If it is dirty, remove it, wash
and clean in the similar manner and install it back
to its place.
– Install the dust bin (11) into the vacuum cleaner
body until clicking.
ATTENTION!
Before installing the dust bin (11) into the vacuum
cleaner body make sure that all filters are dry and there
is no moisture inside the dust bin (11).
Cleaning the outlet air filter (18)
The outlet air filter cleans the air at the final stage
before releasing it from the vacuum cleaner. You can
clean the outlet filter in the following manner:
•
Switch the vacuum cleaner off and unplug it.
•
Remove the outlet filter grid (19) by pressing the
lock (20).
•
Remove the outlet air filter (18).
For easy removing, there are corresponding ledges on
the plastic frame of the outlet air filter.
•
Remove the foam filter from the frame, wash it
under a lukewarm water jet and let it dry. Wash
the filter only with clean water, do not use soap or
detergent. It can damage the filter.
•
Install the foam filter back into the frame, install it
into the vacuum cleaner body and cover with the
grid (19).
Cleaning the vacuum cleaner body
– Wipe the vacuum cleaner body with a soft, slightly
damp cloth and then wipe it dry.
– Do not immerse the body of the vacuum cleaner,
the power cord and the power plug of the unit into
water or other liquids. Provide that no liquid gets
inside the vacuum cleaner body.
– Never use solvents or abrasives to clean the surface
of the vacuum cleaner.
STORAGE
•
Before taking the vacuum cleaner away for long
term storage, clean its body, the dust bin (11) and
the filters (18, 21, 26).
•
For easy storing use the horizontal (15) or the verti-
cal (31) brush storage on the vacuum cleaner body
bottom.
•
Keep the vacuum cleaner in a dry cool place out of
reach of children and disabled persons.
IM VT-8149.indd 5
8/17/20 11:06 AM
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)