VITEK VT-1843 B/R/SR - Инструкция по эксплуатации - Страница 6

6

 ENGLISH

to such rugs. Do not run the turbo brush over 
power cords and turn off the vacuum cleaner 
immediately after you are done using it.

Crevice attachment (23)

The attachment is intended for cleaning of ra-
diators, crevices, corners and between sofa 
pillows. 

Operating instructions

Before using the vacuum cleaner, pull the 
power cord out to the desired length and in-
sert the plug into an outlet. The yellow mark 
on the power cord warns about the maximal 
length of the cord. Never pull the power cord 
past the red mark.
-   Always turn on the vacuum cleaner only 

with the installed container (7), the cone 
filter (20), and the installed НЕРА filters 
(15) and (16) and the foam filter (14).

-   To turn on the vacuum cleaner press the 

On/Off button (11).

-   To wind the cord press the power cord-

winding button (12), and hold the winding 
cord with your hand to prevent whipping 
and damage.

-   During operation you can adjust suction 

power using the suction control, situated 
on the handle of the flexible hose.

Cleaning the vacuum cleaner

Indicator of the dust container filling (10) is 
on when it is necessary to clean the container 
(7).
-   Switch off the unit by pressing the button 

(11) and take the plug out of the socket.

-   Turn the flexible hose tip (5) anticlockwise 

and remove it from the air inlet opening 
(6).

-    Press the clamp button (8), take the handle 

(13) and remove the container (7) from the 
body of the vacuum cleaner.

-    Open the lid of the container (19), by press-

ing the button (18).

-   Remove dust and rubbish from the con-

tainer (7).

-   Close the lid(19).
-   Place the container (7) on its place.

Note:

-   It is recommended to clean the container 

(7) and the cone filter (20) each time after 
usage of the vacuum cleaner.

Cleaning of the input filters 

Keep the НЕРА-filter (15), and the foam filter 
(14) clean, 

as the operational effectiveness of 

you vacuum cleaner depends on it

; clean the 

filters after several usages of the unit 

and if 

they get really dirty – then more often.
-   Switch off the unit by pressing the button 

(11) and take the plug out of the socket.

-   Turn the flexible hose tip (5) anticlockwise 

and remove it from the air inlet opening (6).

-  Press the clamp button (8), take the handle 

(13) and remove the container (7) from the 
body of the vacuum cleaner.

-   Remove the foam filter (14) and the НЕРА 

filter (15).

-   Clean the filters (14 and 15) from dust and 

rubbish.

-   Wash the filters (14 and 15) under warm 

tapping water. Do not use a dish wash ma-
chine to wash the filters.

-   Dry the filters. Do not use a hairdryer to dry 

the НЕРА filter (15).

-   Place the filters on their place.

Cleaning the cone filter

-   Pull the body of the cone filter (20) and re-

move it.

-   Clean the filter (20) from dust and rub-

bish.

-   Wash the filter under a water jet. 
-   Dry and place the cone filter (20) on its 

place by matching the arrow on the filter 
(20) with the arrow on the body of the con-
tainer (7).

Cleaning of the output НЕРА filter

-   Pull the ledge of the input filter grid (17) 

and remove it.

-   Remove the output НЕРА filter (16), wash it 

under a warm water jet and dry. Do not use 
a dish wash machine to wash the filter.

-   Place the filter (16) on its place and close the 

grid (17).

VT_1843_instruk.indd   6

VT_1843_instruk.indd   6

01.07.2011   10:43:13

01.07.2011   10:43:13