VITEK VT-1805 B - Инструкция по эксплуатации - Страница 5

hose is blocked. Unplug the cord and remove 
the blocking substance before you attempt to 
start the vacuum cleaner again.

• Do not operate the vacuum cleaner too 

close to heaters and like radiators, ciga-
rette butts, in areas where flammable or 
combustible liquids are kept.

 • Before you insert the plug into the wall out-

let, make sure your hand is dry.

•  Before you start using the vacuum cleaner, 

please remove large or sharp objects from 
the floor in order to prevent the paper dust 
bag damages.

•  When you want to pull the plug from the wall 

contact, please do this at the plug itself and 
not by means of the electrical cable.

PREPARATION FOR USING

Unpack the vacuum cleaner. Verify the vacu-
um cleaner voltage meets the mains voltage 
in your supply line before switching on. 

Always switch off and unplug the vacuum 
cleaner to change the nozzles or for mainte-
nance. 

VACUUM CLEANER USAGE

•  Verify the dust bag (17 or 23) and inlet filter 

(16) are installed properly.

•  Insert flexible hose end into air intake duct 

(7) and turn it clockwise up to the stop. To 
remove the flexible hose, turn the flexible 
hose end (6) anticlockwise and pull it out 
(Pic.1).

•  Connect plastic extension tube (2) to hose 

handle (4) (Pic. 2).

Plastic extension tubes (2)

•  You can use one or two extension tubes 

while operating. To connect them insert the 
narrow end of one hose in the other hose 
socket. (Pic. 3).

Carpet/floor brush (1)

•  Connect brush (1) to extension tube (2) 

(Pic. 4).

•  Turn the switch on the brush in required po-

sition (depending on surface type which is 
to be cleaned) (Pic. 5, 6).

Crevice nozzle (24)

To clean radiators, slits, corners, spaces be-
tween sofa pillows.

INSTRUCTIONS FOR USE

Before using the appliance, unwind a suf-
ficient length of the cord (19) and insert the 
plug into the power supply. Yellow mark on 
the cord indicates the maximum length of the 
cord. Do not expend the cable beyond the red 
mark. Switch the appliance on only if dust bag 
(17 or 23) and filter (16) are installed prop-
erly. 

 • Push ON/OFF button (11) to switch on the 

appliance.

•  To wind the cord press button (14) while 

holding the cord to escape damages.

•  While operating you can adjust the suction 

power turning regulator handle (12) clock- 
or anticlockwise, and also using mechani-
cal regulator (3) on the flexible hose handle 
(4) (Pic. 2).

MAINTENANCE

Use the appliance only if dust bag (17 or 23) 
and inlet filter (16) are installed properly. If the 
dust bag (17 or 23) or inlet filter (16) is absent, 
the electric motor would be damaged. The 
warranty does not extent to this case.  

•  Press button ON/OFF (11) to switch off the 

appliance and unplug the cord from outlet.

•   Turn flexible hose end (6) anticlockwise and 

unplug it from the vacuum cleaner hous-
ing.

•  Press dust bag compartment cap lock (8) 

and open the cap.

•  Press dust bag lock (15) and take the dust 

bag (17 or 23) out.

•  Remove plastic block lock (18) and unload 

dust and trash from the dust bag.  In case of 
using paper dust bag, just utilize it.

•  Install the plastic block lock on the cloth 

dust bag (17), press the lock (15) and install 

5

       ENGLISH         

Vt-1805.indd   5

Vt-1805.indd   5

26.09.2006   10:28:13

26.09.2006   10:28:13