Thomas Inox 1520 plus - Инструкция по эксплуатации - Страница 11

11

Dry-vacuuming
Important!

The paper filter bag must be fitted when dry- 

vacuuming . Plug in the appliance .

The vacuum cleaner is switched on and off by 

means of he switch located on the motor block 

casing .

Use of tools and accessories

Both suction tubes are inserted into the end of 

flexible hose, as required .

Universal brush nozzle

For use on smooth floors (tiles, stone and PVC) and 

for vacuuming liquids .

Model INOX 1520 S

Upholstery nozzle

For vacuuming upholstered furniture, car seats, 

car boots and smaller uneven surfaces .

Crevice nozzle

For thorough vacuuming of corners, grooves,  

crevices and particularly hard-to-reach places .

G

   Connection for electric tools  

Model INOX 1520 S

The integrated device socket is designed for 

the connection of electric tools with power 

consumption 60 – 2000 Watt .
The electric tool is plugged into the vacuum 

cleaner device socket and the suction hose is 

attached to the relevant connecting point of 

the electric tool .

After use

Switch off the appliance and pull out the plug .

Wind the mains cable loosely in hand and  

store under the carrying handle .

Change the paper filter bag as required .

Vacuuming liquids

Remove the cartridge filter and the paper filter 

bag before vacuuming liquids, as it will otherwise 

disintegrate (see section „Changing the filter“) .

When vacuuming liquids from a container, use 

only the flexible hose or suction tubes .

Always ensure that the float is kept clean and in 

good condition . It acts as a safety device and 

automatically interrupts the flow of air when the 

collecting bin is full .

Take care when vacuuming water from high-sided 

containers or basins where the quantity Ievel 

exceeds the liquid capacity of the collecting bin .

Remember that, in such a case, the water will 

continue to flow from the container even if the 

collecting bin is full and the float has stopped the 

suction flow of the appliance .
Therefore, vacuum only small quantities of water 

at a time and empty the collecting bin before 

switching on again .
Always lift the suction tube out of the water  

before switching off the motor . Pull out the plug .

WARNING! If petrol, paint thinner, fuel 

oil etc. are mixed to mix with suction air 

flow, explosive fumes or compounds may 

be formed.

Acetones, acids and solvents may attack the 

materials on your appliance . 
It is quite safe to vacuum water which contains 

ordinary household cleaning agents . 
After vacuuming liquids, the collecting bin and all 

accessories used should be wiped clean and left to 

dry (see section “Care and maintenance”) .

Changing the filter

Pull out the plug!

Remove the motor block from the collecting bin . 

Hold the paper filter bag by the cardboard inlay 

and pull off from the suction socket .
Place the new paper filter bag inside the collecting 

bin, making sure that the opening located in the 

cardboard inlay is placed in line with the suction 

socket . Then press the filter bag evenly around the 

sides of the collecting bin .
Place the motor block on the collecting bin again 

and secure by means of both snap fasteners .

Care and maintenance

Always pulI out the plug before cleaning the 

appliance! Never immerse the motor block in 

water!

Clean the motor block casing and collecting bin 

with a moist cloth and wipe dry .

If there is a reduction in suction power, change the 

paper filter bag .

If necessary, the collecting bin can be washed out 

with water . Ensure that the bin is completely dry 

before using again .

Rinse out the collecting bin and alI accessories 

with warm, soapy water after wet-vacuuming 

(particularly sticky liquids) .

Do not use abrasive cleaning agents!

Caution!

Replacing the Connecting Cable . 

This unit is equipped with a special connection 

cable which must only be replaced by an 

authorized workshop or customer service center .

Operation