ProfiCare PC-BS 3041 - Инструкция по эксплуатации - Страница 32

PC-BS3041_IM 

06.03.19

32

Telescopic Suction Pipe (2)

The length of the telescopic suction pipe can be adjusted 

individually:
1.  Loosen the locking mechanism by 

sliding and holding the button (3) in 

the direction of the arrow marking.

2. 

Extract one tube from the other to the 

desired length.

3.  Release the button in order to lock the 

connection. 

Mains Cable

Pull the mains cable from the cable compartment. The cable 

compartment is located at the back of the appliance below.

  CAUTION:

•  Pull out the cable up to the maximum length indicated 

with the yellow mark.

•  Never pull the cable out up to the red mark as the 

cable winding can be damaged.

  NOTE:

If the red mark is visible, pull in the cable with the help of 

the cable winding button back to the yellow mark.

Electrical Connection

•  Before connecting the plug to the wall socket, check 

whether the mains voltage is correct. Refer to the infor-

mation on the rating plate of the appliance.

• 

Connect the appliance to a certified wall socket only.

Switching  the Appliance  On / Off

Press the button (14) to switch the appliance on or off.

Suction Control (16)

Turn the suction power control clockwise if you want to 

increase the suction power.
• 

Low suction power:

For curtains, sensitive material.

• 

Moderate suction power:

For deep pile velour carpets and textile floor covering.

• 

High suction power:

For robust carpets and floors.

Using the Appliance

1.  Insert the mains plug into a correctly installed power 

socket. 

2.  Turn the appliance on by the on / off switch by pressing 

down the button.

3. 

Set the “carpet / hard floor” switch, depending on the floor 

covering.

4.  Adjust the suction power with the suction power control.

5.  Vacuum at a steady speed. There is no need to exert 

pressure.

  NOTE:

Pay attention to the range that can be covered with the 

cable length!

Air Slide

Open the air slide on the hose handle in 

order to regulate the airflow or to clear any 

particles sticking to the nozzle.

Switching Off and Winding Up the Mains Cable

1. 

Turn the vacuum cleaner off by the on / off switch and 

remove the plug from the socket. 

2. 

Keep the plug in your hand.

3. 

Press the cable winding button and guide the cable. Hold 

the cable to avoid wrapping.

Maintenance

Dust Bag Replacement Display (11)

Hold the hose up into air. If the display for the vacuum bag 

change shows “red”, the dust bag is full. Please change it.

Changing the Dust Bag

1.  Pull the plug out of the socket.

2. 

Use the opener (8) to open the lid of the dust bag 

compartment.

  NOTE:

The lid can be locked in upright position. Do not push 

the lid beyond the locking mechanism! Otherwise the 

mounting could break away.

3.  Pull out the dust bag holder.

4.  Then pull the dust bag from the holder.

5.  Insert a new bag. Please ensure that the bag is located 

correctly in the guide mechanism. 

6. 

Refit the holder including the dust bag into the dust bag 

compartment. Use the guide rails to do so.

7.  Press down the fastener with the bag. The bag must be 

located completely in the dust bag compartment. Close 

the cover so that it snaps into place.

Filter

Your appliance has two filters.

Motor Protection Filter (Inlet Filter)

The inlet filter is located in the dust bag compartment. The 

filter is located vertically in the rear section of the dust hous

-

ing. Remove the filter by pulling upwards.

Cleaning the Filter Element:

Clean the engine protection filter after 10 dust bag changes. 

If necessary, the filter can also be washed in warm water 

without any additives. Place it back into place only once it is 

completely dry!