Посудомоечные машины Kuppersbusch IGVS 6609.2 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
en
25
Fresh water connection
–
Connect the fresh-water connection to
the tap according to the installation
instructions with the enclosed parts.
Ensure that the fresh-water connection
is not kinked, crushed or twisted.
–
When replacing the appliance, always
use a new water supply hose.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing valve
ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
cold water; hot water max. temperature
60 °C.
Warm water connection *
* depending on model
The dishwasher can be connected to cold
or hot water up to max. 60 °C.
Connection to hot water is recommended
if the hot water can be supplied
by energetically favourable means
and from a suitable installation, e.g. solar
heating system with circulation line.
This will save energy and time.
The hot water setting
‘
:
‹‚
allows you
to adjust your appliance optimally
to operation with hot water.
It is recommended to have a water
temperature (temperature of the incoming
water) of at least 40 °C and no more than
60 °C.
It is not recommended to connect
the appliance to hot water if the water
is supplied from an electric boiler.
Setting hot water:
–
Open the door.
–
Switch on ON/OFF switch
(
.
–
Hold down programme button
#
and
press START button
)"
until
•
:
‹
... is
indicated on the digital display.
–
Release both buttons.
The LED for button
#
flashes and the
digital display
8
displays the factory
setting
•
:
‹…
.
–
Press programme button
#
until the
factory set value
‘
:
‹‹
is indicated on
the digital display
8
.
To change the setting:
–
By pressing the
3
button, you can
switch the hot water setting off
‘
:
‹‹
or
on
‘
:
‹‚
.
–
Press START button
)"
.
The set value is saved.
–
Close the door.
Electrical connection
–
Connect the appliance to an alternating
current only, ranging from 220 V to
240 V and 50 Hz or 60 Hz via
a correctly installed socket with
protective earth conductor. See rating
plate for required fusing
9:
.
–
The socket must be near the appliance
and freely accessible following
installation.
–
The connection may be modified by
technicians only.
–
A power cord extension may be
purchased from customer service only.
–
Use only a residual current operated
circuit-breaker which features the
symbol
‚
. Only this extension
guarantees compliance with the
currently valid regulations.
–
The appliance features a water
damage protection system. Please
note the system will not function
unless
the power supply is connected.
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
