Посудомоечные машины Kuppersbusch IGVS 6609.2 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
en
16
Optical display while the
programme is running *
* depending on model
While the programme is running, a light
spot shines on the floor under the
appliance door. Do not open the
dishwasher door until the light point is no
longer visible on the floor.
If the appliance is installed at eye-level,
with flush furniture front, the light point is
not visible.
This function can be changed as follows:
–
Open the door.
–
Switch on ON/OFF switch
(
.
–
Hold down programme button
#
and
press START button
)"
until
•
:
‹
.... is
indicated on the digital display.
–
Release both buttons.
The LED for button
#
flashes and the
digital display
8
displays the factory
setting
•
:
‹…
.
–
Press programme button
#
until the
factory set value
‚
:
‹‚
is indicated on
the digital display
8
.
To change the setting:
–
By pressing the button
3
, you can
switch the function off
‚
:
‹‹
or on
‚
:
‹‚
.
–
Press START button
)"
.
The set value is saved.
–
Close the door.
Remaining running time display
When the programme is selected, the
remaining running time of the programme
is indicated on the digital display
8
.
The running time is determined during the
programme by the water temperature, the
number of utensils as well as the degree
of soiling and may vary (depending on the
selected programme).
Timer programming
You can delay the start of the programme
in 1 hour steps up to 24 hours.
–
Open the door.
–
Switch on ON/OFF switch
(
.
–
Press the button
`
+ until
‹‚
is
flaching in the timer programming
display
X
.
–
Press + or – button until the
`
displayed time corresponds with your
requirements.
–
Press START button
)"
, timer
programming is activated.
–
To delete timer programming
`
,
press the + or – button until
‹‹
is
indicated on the digital display
X
.
You can change your programme
selection at any time until the
programme starts.
–
Close the door.
End of programme
The programme has ended when the
value
‹
:
‹‹
is indicated on the numerical
display
8
.
The end of the programme is also
indicated by an acoustic signal. This
function can be changed as follows:
–
Open the door.
–
Switch on ON/OFF switch
(
.
–
Hold down programme button
#
and
press START button
)"
until
•
:
‹
.... is
indicated on the digital display.
–
Release both buttons.
The LED for button
#
flashes and the
digital display
8
displays the factory
setting
•
:
‹…
.
–
Press programme button
#
until the
factory set value
›
:
‹ƒ
is indicated on
the digital display
8
.
To change the setting,
–
Press programme button
3
. Each
time the button is pressed, the set
value increases by one level; when the
value of
›
:
‹„
has been reached, the
display jumps back to
›
:
‹‹
(off).
–
Press START button
)"
, the set value
is saved.
–
Close the door.
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
