Bort BWS-1405-R - Инструкция по эксплуатации - Страница 9

9

tion . Prolonged exposure to high intensity noise may 

cause hearing loss .

•  Keep bystanders a safe distance away from work area . 

Anyone entering the work area must wear personal 

protective equipment . Fragments of workpiece or of a 

broken accessory may fly away and cause injury beyond 

immediate area of operation .

•  Hold the power tool by insulated gripping surfaces only, 

when performing an operation where the cutting acces-

sory may contact hidden wiring or its own cord . Cutting 

accessory contacting a “live” wire may make exposed 

metal parts of the power tool “live” and could give the 

operator an electric shock .

•  Position the cord clear of the spinning accessory . If you 

lose control, the cord may be cut or snagged and your 

hand or arm may be pulled into the spinning wheel .

•  Never lay the power tool down until the accessory has 

come to a complete stop . The spinning wheel may grab 

the surface and pull the power tool out of your control .

•  Do not run the power tool while carrying it at your side . 

Accidental contact with the spinning accessory could 

snag your clothing, pulling the accessory into your body .

•  Regularly clean the power tool’s air vents . The motor’s 

fan will draw the dust inside the housing and excessive 

accumulation of powdered metal may cause electrical 

hazards .

•  Do not operate the power tool near flammable materi-

als . Sparks could ignite these materials .

•  Do not use accessories that require liquid coolants . Us-

ing water or other liquid coolants may result in electro-

cution or shock .

Kickback and related warnings

•  Kickback is a sudden reaction to a pinched or snagged ro-

tating wheel, backing pad, brush or any other accessory . 

Pinching or snagging causes rapid stalling of the rotating 

accessory which in turn causes the uncontrolled power 

tool to be forced in the direction opposite of the accesso-

ry’s rotation at the point of the binding . For example, if an 

abrasive wheel is snagged or pinched by the workpiece, 

the edge of the wheel that is entering into the pinch 

point can dig into the surface of the material causing 

the wheel to climb out or kick out . The wheel may either 

jump toward or away from the operator, depending on 

direction of the wheel’s movement at the point of pinch-

ing . Abrasive wheels may also break under these condi-

tions . Kickback is the result of power tool misuse and/or 

incorrect operating procedures or conditions and can be 

avoided by taking proper precautions as given below .

•  Maintain a firm grip on the power tool and position your 

body and arm to allow you to resist kickback forces . 

Always use auxiliary handle, if provided, for maximum 

control over kickback or torque reaction during start-up . 

The operator can control torque reactions or kickback 

forces, if proper precautions are taken .

•  Never place your hand near the rotating accessory . Ac-

cessory may kickback over your hand .

•  Do not position your body in the area where power tool 

will move if kickback occurs . Kickback will propel the 

tool in direction opposite to the wheel’s movement at 

the point of snagging .

•  Use special care when working corners, sharp edges, etc . 

Avoid bouncing and snagging the accessory . Corners, 

sharp edges or bouncing have a tendency to snag the 

rotating accessory and cause loss of control or kickback .

•  Do not attach a saw chain woodcarving blade or 

toothed saw blade . Such blades create frequent kick-

back and loss of control .

Safety warnings specific for polishing 

operations

•  Do not allow any loose portion of the polishing bonnet 

or its attachment strings to spin freely . Tuck away or 

trim any loose attachment strings . Loose and spinning 

attachment strings can entangle your fingers or snag on 

the workpiece .

Safety warnings specific for sanding operations

•  Do not use excessively oversized sanding disc paper . Fol-

low manufacturers recommendations, when selecting 

sanding paper . Larger sanding paper extending beyond 

the sanding pad presents a laceration hazard and may 

cause snagging, tearing of the disc, or kickback .

Safety warnings specific for wire brushing 

operations

•  Be aware that wire bristles are thrown by the brush even 

during ordinary operation . Do not overstress the wires 

by applying excessive load to the brush . The wire bristles 

can easily penetrate light clothing and/or skin .

•  If the use of a guard is recommended for wire brushing, 

do not allow any interference of the wire wheel or brush 

with the guard . Wire wheel or brush may expand in 

diameter due to work load and centrifugal forces .

Additional safety warnings

•  Wear safety goggles .

•  Use suitable detectors to determine if utility lines are 

hidden in the work area or call the local utility company 

for assistance . Contact with electric lines can lead to 

fire and electric shock . Damaging a gas line can lead 

to explosion . Penetrating a water line causes property 

damage or may cause an electric shock .

•  Release the On/Off switch and set it to the off position 

when the power supply is interrupted, e . g ., in case of 

a power failure or when the mains plug is pulled . This 

prevents uncontrolled restarting .

•  Do not touch grinding and cutting discs before they 

have cooled down . The discs can become very hot while 

working .

•  Secure the workpiece . A workpiece clamped with 

clamping devices or in a vice is held more secure than 

by hand .

MAINTENANCE AND CLEANING

Make sure that the machine is not live when carry-

ing out maintenance work on the motor .