Makita N5900B - Инструкция по эксплуатации - Страница 4

4 

ENH101-7 

EC-DECLARATION OF CONFORMITY 

Model; N5900B 

We declare under our sole responsibility that this 
product is in compliance with the following standards of 
standardized documents; 
EN60745, EN55014, EN61000 in accordance with 
Council Directives, 2004/108/EC, 98/37/EC. 

CE2006

000230 

Tomoyasu Kato 

Director 

Responsible Manufacturer: 

Makita Corporation

3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN 
Authorized Representative in Europe: 

Makita International Europe Ltd.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 
8JD, ENGLAND 

GEB013-1 

SPECIFIC SAFETY RULES 

DO NOT let comfort or familiarity with product 
(gained from repeated use) replace strict adherence 
to circular saw safety rules. If you use this tool 
unsafely or incorrectly, you can suffer serious 
personal injury. 
Danger: 

1. 

Keep hands away from cutting area and the 
blade. Keep your second hand on auxiliary 
handle, or motor housing.

 If both hands are 

holding the saw, they cannot be cut by the blade. 

2. 

Do not reach underneath the workpiece.

 The 

guard cannot protect you from the blade below the 
workpiece. Do not attempt to remove cut material 
when blade is moving. 
CAUTION: Blades coast after turn off. Wait until 
blade stops before grasping cut material. 

3. 

Adjust the cutting depth to the thickness of 
the workpiece.

 Less than a full tooth of the blade 

teeth should be visible below the workpiece. 

4. 

Never hold piece being cut in your hands or 
across your leg. Secure the workpiece to 
stable platform.

 It is important to support the 

work properly to minimize body exposure, blade 
binding, or loss of control. 

A typical illustration of proper hand support, workpiece 
support, and supply cord routing (if applicable).

000157 

5. 

Hold power tool by insulated gripping 
surfaces when performing an operation where 
the cutting tool may contact hidden wiring or 
its own cord.

 Contact with a "live" wire will also 

make exposed metal parts of the power tool "live" 
and shock the operator. 

6. 

When ripping always use a rip fence or 
straight edge guide.

 This improves the accuracy 

cut and reduces the chance of blade binding. 

7. 

Always use blades with correct size and shape 
(diamond versus round) of arbour holes.

Blades that do not match the mounting hardware 
of the saw will run eccentrically, causing loss of 
control. 

8. 

Never use damaged or incorrect blade 
washers or bolt.

 The blade washers and bolt 

were specially designed for your saw, for optimum 
performance and safety of operation. 

9. 

Causes and Operator Prevention of Kickback: 

−

kickback is a sudden reaction to a pinched, 
bound or misaligned saw blade, causing an 
uncontrolled saw to lift up and out of the 
workpiece toward the operator; 

−

when the blade is pinched or bound tightly by 
the kerf closing down, the blade stalls and the 
motor reaction drives the unit rapidly back 
toward the operator; 

−

if the blade becomes twisted or misaligned in 
the cut, the teeth at the back edge of the 
blade can dig into the top surface of the wood 
causing the blade to climb out of the kerf and 
jump back toward the operator. 

Kickback is the result of saw misuse and/or 
incorrect operating procedures or conditions and 
can be avoided by taking proper precautions as 
given below. 

• 

Maintain a firm grip with both hands on the 
saw and position your arms to resist 
kickback forces. Position your body to 
either side of the blade, but not in line with 
the blade.

 Kickback could cause the saw to 

jump backwards, but kickback forces can be 
controlled by the operator, if proper 
precautions are taken.